Audio-Technica U857QU DVR User Manual


 
• Designed for high-quality
sound reinforcement,
professional recording and
broadcasting
• UniLine
polar pattern
provides narrow 90°
acceptance angle
• Superior off-axis rejection for
maximum gain before
feedback
• UniGuard
RFI-shielding
technology offers outstanding
rejection of radio frequency
interference (RFI)
• Easy-to-adjust, rugged,
small-diameter, alternating
gooseneck with virtually no
“memory” permits quick
positioning into desired shape
• UniSteep
®
filter provides a
steep low-frequency
attenuation to improve sound
pickup without affecting voice
quality
Self-contained electronics eliminate need for external power
module
Accepts interchangeable elements to permit angle of
acceptance from 90° to 360°
Two-stage foam windscreen yields dramatically improved
resistance to P-pops and other breath blasts
Quick-mount design with 3-pin XLRM-type connector insert at
base plugs into any standard XLRF-type surface or cable
connector
Included shock mount attenuates noise, shock and vibration
transmitted through the mounting surface
The U857QU stands 19.17" (487.0 mm) from the table or podium; it
is also available in a 23.74" (603.0 mm) version as U857QLU. The
two models are identical in all other respects.
The U857QU requires 11V to 52V phantom power for operation.
Output from the microphone’s XLRM-type connector is low
impedance (Lo-Z) balanced. The signal appears across Pins 2 and
3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive
acoustic pressure produces positive voltage at Pin 2.
An integral 80 Hz high-pass UniSteep
®
filter provides easy
switching from a flat frequency response to a low-end roll-off. The
roll-off position reduces the microphone’s sensitivity to popping
in close vocal use. It also reduces the pickup of low-frequency
ambient noise (such as traffic, air-handling systems, etc.), room
reverberation and mechanically coupled vibrations.
A
void leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods.
Extremely high humidity should also be avoided.
Fréquence - Hertz
LÉGENDE
12" ou plus sur l'axe
Pente de diminution
Réponse en Fréquence
Réponse - dB
8 kHz
200 Hz
1 kHz
5 kHz
Directivité
ÉCHELLE: 5 dB PAR DIVISION
LÉGENDE
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG Angleterre
www.audio-technica.com
P51692 ©2005 Audio-Technica U.S., Inc. Imprimé aux E.U.
8 kHz
Polar Pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz
1 kHz
5 kHz
F
requency in Hertz
LEGEND
12" or more on axis
Roll-off
Frequency Response
Response in dB
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51692 ©2005 Audi
o-Technica U.S., Inc. Printed in U.S.A.
U857QU /U857QLU
U857QU/U857QLU SPECIFICATIONS
ELEMENT Fixed-charge back plate
per
manently polarized condenser
POLAR P
ATTERN
Line Cardioid
FREQ
UENCY RESPONSE
30-20,000 Hz
LO
W FREQUENCY ROLL-OFF
80 Hz, 18 dB/octa
ve
OPEN CIRCUIT SENSITIVITY –35 dB (17.7 mV) re 1V at 1 Pa*
IMPED
ANCE
250 ohms
MAXIMUM INPUT SOUND LEVEL 135 dB SPL, 1 kHz at 1%
T.H.D.
D
YNAMIC RANGE
(typical)
115 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO
1
74 dB, 1 kHz at 1 Pa*
PHANT
OM POWER REQUIREMENTS
11-52V DC
, 2 mA typical
SWITCH Flat, roll-off
WEIGHT
U857Q
U
5.7 oz (161 g)
U857QLU 5.9 oz (167 g)
DIMENSIONS
U857Q
U
19.17" (487.0 mm) long
U857QLU 23.74" (603.0 mm) long
BO
TH
0.48" (12.2 mm) head diameter
,
0.74 (18.9 mm) base diameter
OUTPUT CONNECT
OR
Integ
ral 3-pin XLRM-type
OPTIONAL INTERCHANGEABLE UE-C cardioid (120°);
ELEMENTS UE-H h
ypercardioid (100°);
UE-O omnidirectional (360
°)
A
CCESSORIES FURNISHED
A
T8154 two-stage foam
windscreen;
AT8662 shock mount
In the interest of standards development, A.T.U.S.offers full details on its test
methods to other industr
y professionals on request.
*1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice
.
U857Q/U857QL CARACTÉRISTIQUES TECHNIQUES
TYPE Condensateur polarisé en
permanence avec plaque fixe à
charge fixe
DIRECTIVITÉ Cardioïde-ligne
RÉPONSE EN FRÉQUENCE 30-20 000 Hz
ATTÉNUATION DES GRAVES 80 Hz, 18 dB/octave
NIVEAU DE SORTIE –35 dB (17,7 mV) réf 1V/Pa*
IMPÉDANCE 250 ohms
NIVEAU DE PRESSION 135 dB SPL, 1 kHz à 1% T.H.D.
ACOUSTIQUE MAXIMAL
DYNAMIQUE (typique) 115 dB, 1 kHz à SPL max.
RAPPORT SIGNAL/BRUIT
1
74 dB, 1 kHz/Pa*
ALIMENTATION FANTÔME 11-52V CC, 2 mA typiques
COMMUTATEUR Plat, atténuation
POIDS
U857QU
161 g (5,7 oz)
U857QLU 167 g (5,9 oz)
DIMENSIONS
U857QU
Longueur 487,0 mm (19,17 po)
U857QLU Longueur 603,0 mm (23,74 po)
LES DEUX Diamètre de la tête 12,2 mm
(0,48), diamètre de la base
18,9 mm (0,74 po)
CONNECTEUR DE SORTIE Type XLRM 3 broches intégré
CAPSULES INTERCHANGEABLES UE-C cardioïde (120°);
EN OPTION UE-H hypercardioïde (100°);
UE-O omnidirectionnel (360°)
ACCESSOIRES FOURNIS AT8154 bonnette anti-vent en
mousse double épaisseur ;
AT8662 suspension anti-choc
Afin de contribuer au développement des normes, A.T.U.S.fournit tout renseignement
sur ses méthodes de test aux professionnels de l’industrie qui en font la demande.
*1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typique, pondéré en A, mesuré avec l’Audio Precision System One.
Les caractéristiques techniques sont soumises à des changements sans préavis.
UNILINE
CONDENSER QUICK-MOUNT
GOOSENECK MICROPHONES
• Conçu pour le renforcement
sonore, l’enregistrement
professionnel et la
radiodiffusion de haute qualité
• Directivité UniLine
fournissant un angle
d’acceptance étroit de 90°
• Rejet hors axe supérieur pour
un gain avant accrochage
maximal
• Excellent rejet des
interférences rf
• Col de cygne de faible
diamètre, robuste et facile à
régler pour un positionnement
rapide dans la forme voulue
• Filtre UniSteep
®
pour une
forte atténuation des basses
fréquences ; améliore la prise
de son sans affecter la qualité
de la voix
Système électronique autonome permettant de ne pas avoir
besoin de module d'alimentation externe
Peut recevoir des capsules interchangeables, ce qui permet
d’avoir un angle d’acceptance allant de 90° à 360°
Bonnette anti-vent en mousse double épaisseur, offrant une très
haute résistance aux plosives et bruits de souffle en général
Conçu pour une fixation rapide avec un connecteur de type
XLRM à 3 broches à la base se connectant à n’importe quel
connecteur de câble ou de surface de type XLRF standard
La suspension anti-choc fournie atténue les bruits, chocs et
vibrations transmis par la surface de montage
Le U857QU est haut de 487,0 mm (19,17 po) par rapport à la table
ou au podium ; il est également disponible en version 603,0 mm
(23,74 po), modèle U857QLU. Pour le reste, ces deux modèles
sont en tous points identiques.
Le U857QU fonctionne sur alimentation fantôme de 11V à 52V.
La sortie du microphone est symétrique basse impédance, XLR
male, 3 broches. Le signal symétrique est entre les broches 2 et 3,
le point chaud est en deux (la tension positive sur le point chaud
est générée par une pression acoustique positive sur la capsule).
La masse (blindage) est sur la broche 1.
Un filtre passe-haut 80 Hz intégré UniSteep
®
permet de passer
facilement de la réponse en fréquences plate à l’atténuation des
graves. La position passe-haut sert à rendre le microphone moins
sensible aux “pops” quand il est utilisé en proximité sur voix. Elle
sert également à réduire la sensibilité aux bruits ambiants de basse
fréquence (dus au trafic, aux installations de ventilation, etc.),
à la réverbération de la pièce et aux vibrations couplées
mécaniquement.
Evitez de laisser le microphone en plein soleil ou dans des endroits
où la température est supérieure à 43°C (110°F) pendant une
durée prolongée. Une trop forte humidité doit également être
évitée.
U857QU /U857QLU
MICROPHONES COL DE CYGNE À
CONDENSATEUR UNILINE
À FIXATION RAPIDE
Installation de la
suspension anti-choc
Caractéristiques
dimensionnelles pour
l’installation de l’AT8662
A. Trous de guidage de
1,5 mm (
1
/
16
po) en
3 endroits différents
sur un cercle de
58,2 mm (2,29 po)
B. Trou débouchant de
51,0 mm (2,0 po)
pour insertion de la
suspension
C. Rebord extérieur du
collet, diamètre
71,0 mm (2,79 po)
Le schéma n’est pas à la taille rélle.
1. Trouvez le centre de la surface de fixation et marquez-le.
Prévoyez assez d’espace pour disposer le collet de la
suspension anti-choc sur la surface et assurez-vous qu’il n’y
a pas d’objet faisant obstruction sous la surface de fixation.
2. En utilisant une perceuse de 51,0 mm (2,0 po), faites le grand
trou pour la suspension anti-choc.
3. Insérez la suspension anti-choc dans le trou et marquez
l’emplacement des trois trous de vis de fixation. Assurez-vous
que la suspension est bien au centre du grand trou
avant de
marquer l’emplacement des trois petits trous de vis de
fixation.
4. En utilisant un foret de 1,5 mm (
1
/
16
po), percez trois trous de
guidage pour les vis de fization.
5. Après avoir installé le microphone, donnez du mou au cable
de connexion pour que votre suspension soit au maximum de
son efficacité.
Shock Mount Installation
AT8662 mounting dimensions
A.
1
/
16
" (1.5 mm) pilot
holes 3 places on
2.29" (58.2 mm) circle.
B. 2.0" (51.0 mm)
through-hole for mount
clearance
C. Outside edge of
flange, 2.79"
(71.0 mm) diameter
Drawing not actual size.
1. Find the center of the mounting location and mark it. Allow
enough clearance to accommodate the shock mount's flange
on the surface and make certain there are no physical
obstructions below the desired location.
2. Using 2.0" (51.0 mm) hole saw, drill the large through-hole for
the shock mount.
3. Set the shock mount into the hole and mark the location of the
three mounting screw holes.
Make certain to “center” the
mount in the large hole before marking the three small
mounting screw locations.
4. Using a
1
/
16
" (1.5 mm) drill bit, drill three pilot holes for the
mounting screws.
5.
After installing the microphone, assure maximum shock
mounting effectiveness by providing some slack in the
connecting cable.