Filter
Top Products
POWERPOWER
11 22 33
44
77
55
8 8
00
66
99
ENTERENTER
IN 8IN 8
TUNE-TUNE-
SAVESAVE
MENUMENU
EXITEXIT
LOUDLOUD
OFFOFF
MUTEMUTE
IN 9IN 9
+10+10
AMAM
MM
T+T+
S+S+
FMFM V+V+ T-T- S-S-
B &K Components, Ltd.
Model MZ-128
SELSEL
ENTERENTER
VOLUMEVOLUME
PRESETPRESET
ON/OFFON/OFF
B+B+
B-B-
Õ
®
°
¯
ZONEZONE
VIDEO +VIDEO +
BASSBASSTREBLETREBLE SOURCESOURCE
ST/MST/M
LOUDNESSLOUDNESS
DEDICATEDDEDICATED
D-IND-IN
TUNE+TUNE+ STA-STA-
STA+STA+
UPUP
DOWNDOWN
L
E
F
T
L
E
F
T
R
I
G
H
T
R
I
G
H
T
B & K CT Series MZ-128 Remote Controller Reference Sheet
The MZ-128 Remote Controller has multiple useful functions:
1) The MZ-128 Remote Controller may be used to control and setup a CT610/310/600.
2) The learning keypads etc...
3) The may be set to source code sets 000-128
and 999.
MZ-128 may be used as a source of IR for use in programming
MZ-128 the B & K IR functions listed below, for
Setup the MZ-128 to use a discrete B & K code set:
1) Install 4 AAA batteries into the remote. Observe polarity.
2) Press and hold the B & K and MUTE buttons simultaneously for two seconds. The LED will
light up solid red and stay illuminated.
3) Firmly press the desired B & K three digit code set. Always use three digits (i.e. 0-1-1 default
for Zone A)
4) Press the B & K button again to confirm setup. The red LED will blink three times when the IR
CODE SET 000-128
MZ-128 BUTTON B & K IR FUNCTION MZ-128 BUTTON B & K IR FUNCTION
[POWER STATE] [TUNER]
B&K POWER ON AM SELECT THE AM BAND
POWER POWER TOGGLE FM SELECT THE FM BAND
OFF POWER OFF TUNE + TUNE FREQUENCY UP
TUNE - TUNE FREQUENCY DOWN
[VOLUME] STA + TUNER FAV PRESET UP
MUTE MUTE TOGGLE STA - TUNER FAV PRESET DOWN
VOLUME MASTER VOL UP M STEREO / MONO
VOLUME MASTER VOL DOWN
[NAVIGATION]
[TONE CONTROL] MENU MENU UP/DOWN LEVEL
B+ BASS UP LEFT LEFT OR BALANCE (L)
B- BASS DOWN RIGHT RIGHT OR BALANCE (R)
T+ TREBLE UP SEL/ENTER SELECT OR ENTER
T- TREBLE DOWN UP UP
LOUD LOUDNESS TOGGLE DOWN DOWN
SAVE SAVE
[INPUT SOURCE] EXIT TOTAL EXIT FROM ALL MENUS
S+ SOURCE UP ZONE ZONE SELECT
S- SOURCE DOWN
V+ VIDEO SOURCE UP [NUMERIC]
D-IN ZONE DEDICATED IN 0 0
AM TUNER AM 1 1
FM TUNER FM 2 2
IN 1 IN 1 OR [V1] 3 3
IN 2 IN 2 OR [V2] 4 4
IN 3 IN 3 OR [TV] 5 5
IN 4 IN 4 OR [DVD] 6 6
IN 5 IN 5 OR [CD] 7 7
IN 6 IN 6 OR [SAT] 8 8
IN 7 IN 7 OR [TAPE] 9 9
IN 8 IN 8 OR [V4] +10 +10
IN 9 IN 9 OR [V5]
[FAVORITE PRESET]
PRESET FAVORITE PRESET UP
PRESET FAVORITE PRESET DN
CODE SET 999
MZ-128 BUTTON B & K IR FUNCTION
[B & K ALL COMMANDS]
ON/B & K/POWER ALL B & K POWER ON
OFF ALL B & K POWER OFF
VOLUME ALL B & K VOLUME UP
VOLUME ALL B & K VOLUME DOWN
0 ALL B & K VOLUME 0 DB
2 ALL B & K VOLUME -20 DB
4 ALL B & K VOLUME -40 DB
6 ALL B & K VOLUME -60 DB
MUTE ALL B & K MUTE TOGGLE
B &K B & K
MZ-128 Default Factory Code-Set is: 0-0-0 Whole House Control
Code-Set 128 Simply Explained
Code-Set 128 is a special code-set which
allows individual control of the Hardware Zone
that the IR Data is received by. It will not function
when received by the unit’s front panel. I.e., Two
keypads are plugged into Zone A & B’s Control
I/O Ports, when the remote comes into IR view
of the keypad in Zone A, the 128 Code-set
remote will only control Zone A, when in Zone A.
Take that same remote into Zone B and it will
only control Zone B.