Filter
Top Products
Model 973-315LM Security✚
®
3-Button Remote Control
The 900 Series remote control works only with door openers and
light controls having an orange “Learn” button.
Programming instructions are described and illustrated below.
The additional push buttons can also activate other garage door
openers and/or light controls. (Instructions for programming light
products are included with those accessories.)
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THEREARE NO OTHERUSER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
© 2006, Chamberlain Group Inc.
114A2572D All Rights Reserved
The Remote Control Batteries
The lithium batteries should produce
power for up to 5 years. To replace,
pry open case with visor clip or
screwdriver, as shown. Insert
batteries positive side up (+).
Dispose of old batteries properly.
Replacement Parts
3V2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . . .10A20
Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137
Battery
positive
side up (+)
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
WARNING
CAUTION
WARNING
WARNING
OWNER’S MANUAL
Instructions are Described and Illustrated Below
"A"
Button
"B"
Button
1. Remove the cover from the Lighted Door
Control.
2. Press and hold the button on the
hand-held remote that you wish to operate
your garage door.
3. While holding the remote button, press
and hold the “A” button on the Lighted
Door Control.
4. Continue holding both buttons while you
press the “B” button on the Lighted Door
Control (all three buttons are held).
5. Release buttons when the motor unit
lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be
heard.
1. Press and hold the button on the
hand-held remote that you wish to
operate your garage door.
2. While holding the remote button, press
and hold the light button on the
Multi-Function Door Control.
3. Continue holding both buttons while you
press the push bar on the Multi-Function
Door Control (all three buttons are held).
4. Release buttons when the motor unit
lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be
heard.
L
O
C
K
L
I
G
H
T
L
O
C
K
L
I
G
H
T
If you have a lighted push button that looks like the lighted
push button illustrated follow the instructions below.
If you have a multi-function wall control follow instructions
below.
Press and release the “learn” button on the motor unit. The learn
indicator light will glow steadily for 30 seconds. Within 30
seconds, press and hold the button on the hand-held remote.
Release the button when the motor unit light blinks. It has learned
the code. If light bulbs are not installed, two clicks will be heard.
If neither of the two programming instructions match your
type and style of opener follow instructions below.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor unit
until the learn indicator light goes out
(approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or
keyless entry you wish to use.