Dynex DX-TVM102 TV Mount User Manual


 
Maintenance
To remove the TV from the wall bracket, pull down on the release straps, pull the bottom
of the TV away from the wall bracket, then lift the TV completely off the wall bracket.
< 16 mm
(5/8 in.)
2x
M4 x 12mm
M5 x 12mm
M6 x 12mm
M6 x 20mm
M4 x 30mm
M5 x 30mm
M6 x 35mm
M4 / M5 M6
M4 / M5
M6
5/16 in.
5/16 x 2.5 in.
3/16 in.
1/2 in.
Attach the wall bracket to the wall studs.
Caution: Avoid potential injuries or property damage!
Any material covering the wall must not exceed 16 mm
(5/8 in.).
Caution: Avoid potential injury or property damage! Do
not overtighten the lag bolts [Q]. Tighten the lag bolts
[Q] only until the washers [O] are pulled firmly against
the wall bracket [A].
1
DX-TVM102 Slim-Profile TV Mount
USER GUIDE
ENGLISH 09-0602
Attach the TV bracket
Step 2a: TVs with flat back panels.
Step 2b: TVs with rounded or angular back panels.
Optional: Use washer [K] with M4 or M5 hardware only.
2
Mount the TV to the wall bracket
First mount the top hooks of the TV brackets onto the wall bracket, then press
the bottom of the TV brackets against the wall bracket until they snap into place.
5
Adjust the release straps length
Adjust the release straps so they are level
with bottom of the TV; this allows the
straps to be accessible, yet concealed,
when the TV is on the wall.
3
Set the viewing angle (optional)
Attach the tilt brackets.
4
Supplied parts and hardware
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged,
do not return the item to your dealer, but contact Customer Service. Never use damaged parts.
PARTS LIST
Note: Not all parts will be used
Missing parts? Call 800-573-2860
A Wall bracket (1)
B Left TV bracket (1)
C Right TV bracket (1)
D M4 × 0.47" (12 mm) screws (4)
E M5 × 0.47" (12 mm) screws (4)
F M6 × 0.47" (12 mm) screws (4)
G M6 × 0.79" (20 mm) screws (4)
H M4 × 1.18" (30 mm) screws (4)
I M5 × 1.18" (30 mm) screws (4)
J M6 × 1.38" (35 mm) screws (4)
K M4/M5 washer (8)
L M6 washer (4)
M M4/M5 spacer (4)
N M6 spacer (4)
O 5/16" (7.9 mm) washer (2)
P Tilt bracket (2)
Q 5/16" × 2.5" (63.5 mm)
lag bolt (2)
R Carriage bolt (4)
S Nylock nut (4)
Tools you will need:
• Power drill
3/16" wood drill bit
• Phillips screwdriver
• Level
Socket wrench with 1/2 in. socket
• Pencil
• Stud finder
• Adjustable wrench
• Awl
Important safety instructions
The DX-TVM102 TV mount is designed to support a Flat Panel TV weighing up to 50 lbs. (22.7 kg).
Caution
The DX-TVM102 is designed for use in wood frame walls only! The weight of your TV must not exceed 50 lbs. (22.7 kg). The wall must be
capable of supporting five times the weight of the TV and wall mount combined.
Do not use this product for any purpose not explicitly specified by Dynex. Improper installation may cause property damage or
personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service
or call a qualified contractor. Dynex is not responsible for damage or injury caused by incorrect installation or use.
Warning
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.
© 2009 Best Buy Enterprise Services, Inc. All rights reserved. DYNEX is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.
6907-002001 <00>
63.5 mm
(2.5 in.)
3/16 in.
5 mm
HEAVY! You will need
assistance with this step.
[Latched]
[Unlatched]