Freestyle 788 Watch User Manual


 
HOW TO SET AND OPERATE THE
ALARMS AND HOURLY CHIME
From normal time mode, press
Mode button LB twice to enter the
alarm mode. Normal time remains
on the lower row, alarm time on the
upper row. Pressing
Reset button
RB will toggle between alarm 1,
indicated by the left “ ” flag, and
alarm 2, indicated by the right
“ ” flag. Alarm 1 is a daily,
repeating alarm, and alarm 2 is a
one time only reminder alarm.
Press and hold
Light/Set button LT
for approximately three seconds to
enter alarm setting mode. The min-
utes digit will flash. Press Start/Stop
button RT to advance the flashing
minutes digit.
Press
Mode button LB to advance
tens of minutes. Press Start/Stop
button RT to advance the flashing
tens of minutes digit.
Press mode button
LB to advance the
hours digit. Press Start/Stop button
RT to advance the flashing hours
digit. While setting the flashing hours
digit, “
A” or “P” is displayed on the
right side. “A” designates a.m. and “P
designates p.m.
Press
Light/Set button LT to exit
the alarm setting mode. To activate
the alarm while in alarm mode:
Press
Start/Stop button RT to
arm or disarm the alarm “ ” and/or
hourly chime “ ”. Note the setting
sequence is: alarm on, chime on,
both alarms and chime on, both
alarms and chime off.
788 SHARK WATCH
INSTRUCTIONS
FEATURES:
• CURRENT TIME (HR., MIN.,
& SEC.)
• DAY/MONTH/DATE
• CHRONOGRAPH WITH SPLIT
& LAP TIMES
• DUAL ALARMS ( 1 DAILY
REPEATING, 1 NON-
REPEATING REMINDER.)
COUNTDOWN, COUNTDOWN
REPEAT, COUNTDOWN CHRONO
LAP & COUNTDOWN CHRONO
SPLIT TIMERS
• DUAL TIME
• HOURLY CHIME
• OPTIONAL 24-HR. TIME
(MILITARY TIME. )
• WATER RESISTANT TO
300 FT.
• NIGHT VISION
ELECTRO-
LUMINESCENT BACKLIGHTING
NORMAL TIME MODE
( The term “Mode” means the func-
tion status of the watch.) Normal
time mode shows hours, minutes,
seconds, day and date. To set time,
see operating instructions on How
to Set Normal Time.
NORMAL TIME MODE
KEY TO SYMBOLS
LT - Left Top (Light/Set)
LB - Left Bottom (Mode)
RT - Right Top (Start/Stop)
RB - Right Bottom (Reset)
HOW TO SET NORMAL TIME,
DATE AND 24-HOUR FORMAT
Note: If no buttons are pressed for
approximately ten seconds, the
watch will exit the setting mode.
From
Normal Time mode, press
and hold the
Light/Set button LT
for approximately three seconds;
the seconds digits will flash.
Pressing the
Start/Stop button RT
will reset the seconds digits to 0. If
seconds are greater than 30, one
will be added to the minutes digit.
To set minutes, press
Mode button
LB; single minutes digit will flash. To
advance flashing minutes digit, press
Start/Stop button RT; hold for
rapid
advance.
To set tens of minutes, press Mode
button LB; tens of minutes will flash.
To advance flashing tens of minutes
press Start/Stop button RT; hold for
rapid advance.
Continuing through the setting
mode, the setting sequence is a
continuous loop of: seconds • single
minutes •tens of minutes • hours •
day/month/date • 12/24-hour mode,
and looping back to seconds. When
setting is complete, press
Light/Set
button LT to return to normal time
mode.
HOW TO OPERATE
CHRONOGRAPH/STOPWATCH
The chronograph will record a
maximum of 99 hours, 59 minutes
and 59 seconds. Press
Mode
button LB once from normal time
mode to enter the chronograph
mode. Normal time will remain on
the lower row, chronograph on the
upper row. “ ” flag will be displayed.
Reset the chronograph to zero by
pressing
Reset button RB. Press
the
Light/Set button LT to switch
between Lap and Split mode.
(“
LP” flag will be displayed for lap
mode and “ ” flag will be dis-
played for split time mode.)
Split time is the time elapsed since
the start of the chronograph. To use
the split time feature, “ ” flag must
be displayed. Press
Start/Stop
button RT to start chronograph.
“ ” flag will begin flashing. Press
Reset button RB to view split time.
Chronograph will continue to count
while split time is displayed. To
release split time and return to run-
ning chronograph, press
Reset but-
ton RB.
Each press of Reset button RB will
display a split time.
To stop chronograph, press
Start/Stop
button RT. Reset the chronograph to
zero by pressing the Reset button RB.
Lap time is the time elapsed since the
previous lap. To use the lap time
feature, “
LP” flag must be displayed.
Reset the chronograph to zero by
pressing the Reset button RB. Enter
LAP mode by pressing
Light/Set but-
ton LT. Press Start/Stop button RT to
start chronograph. “LP” flag will begin
flashing. Press Reset button RB to
view lap time. Chronograph will start
counting next lap while lap time is
displayed. To release lap time and
return to running chrono, press
Reset
button RB. Each press of Reset but-
ton RB will display a lap time.
To stop chronograph, press
Start/Stop button RT. Reset the
chronograph to zero by pressing
the
Reset button RB.
continued...
®