Filter
Top Products
39 -
Use the rotary switch if you want to switch over a VCR, DVD
device or a Set Top Box.
Press the END and EPG buttons simultaneously for at least
5 seconds. The upper left indicator on the remote control will
blink twice.
Enter the four numbers in sequence that you found in the code
list (e.g. 0539 for Loewe DVD player).
After each number you enter, the indicator will blink once, after the last number
it will blink twice. If the number was incorrect, the indicator will remain lit
longer. The code number was not accepted. If the code was accepted with two
blinks, you can test the functions of the device you just programmed.
If the device cannot be operated or can only be operated poorly, repeat the
code entry with the next code from the list. If there are no other codes specifi ed
for this manufacturer, try it using the code suggestions from the remote control.
Setting the remote control using the suggestions from the
remote control
Switch the device on that you want to switch over to the remote control.
Standby mode is not enough.
Use the rotary switch if you want to switch over a VCR, DVD
device or a Set Top Box.
Press the END and EPG buttons simultaneously for at least
5 seconds. The upper left indicator on the remote control will
blink twice.
Enter the the numbers 991 in sequence. The indicator will
blink once after each number entered.
Press the # PIP button to select the fi rst code.
Point the remote control toward the device you want to switch over to the
remote control. Observe that device.
Now press the button (Play) or On/Off on the remote
control.
Wait a moment for the device to react. If the device does not
react, then that was not the right code. Press the # PIP button
again to call the next code.
Press the button (Play) or On/Off again.
If the device reacts, press the EPG button to adopt the
code.
Operating additional equipment
Operating other Loewe devices with the RC3 remote control
Using this remote control, you can operate additional devices from Loewe.
Use the rotary switch to select VCR, TV or a Set Top Box.
The following are preset at the factory: Loewe VCRs, Loewe TV
sets and for STBs (Set Top Box) in Germany, the
common d-box.
Use the driver buttons in the TV and STB position for VCR,
DVD or Digital Recorder
You can switch over the six drive buttons
(
, , , , , ), both for the TV and for the
STB, to control a VCR or DVD player/recorder (the control of the integrated
"Digital Recorder Plus" is preset at the factory):
First set the switch to the main function TV or STB.
Then press the END and EPG buttons simultaneously for at
least 5 seconds. The upper left indicator on the remote control
will blink twice.
Enter the the numbers 988 in sequence. The indicator will
again blink two times.
Now set the switch to the desired function for the drive
buttons:
to DVD, VCR or to TV, if the digital recorder is to be operated.
Press the # PIP button to complete the setting. The indicator
will blink two times.
Setting the remote control to operate devices from other
manufacturers
You can switch over the remote control for other VCRs, DVD players and Set Top
Boxes if the infrared code for the device type is listed in the code list or if it is
included in the code memory of the RC3.
Even if the manufacturer of the device is listed in the code list, it may not
be possible to operate that device using the Loewe remote control.
Setting the remote control using code entry
Search for the code number for your device in the code list (see as of pages
48-52). The list is arranged according to device type – DVD, VCR, STB – and
alphabetically according to manufacturer. Next to the manufacturer’s name, you
will fi nd one or more code numbers.
TV
DVD STB
VCR
PIP
EPG
END
wxyz
wxyz
AV
jkl
def
wxyz
PIP
EPG
TV
DVD STB
VCR
TV
DVD STB
VCR
PIP
tuv
tuv
wxyz
TV
DVD STB
VCR
TV
DVD STB
VCR
EPG
END
EPG
END