Filter
Top Products
24
Setting Up VCR Plus+ (cont'd)
Now, compare the channel numbers you
have written in the GUIDE CH. and
USER CH. columns. You'll notice that
some stations have guide and user chan-
nel numbers that are the same, and other
stations have channel numbers that do
not match. Where the channel numbers
DO NOT match, you must tell the VCR
the guide and user channel numbers
according to the following steps.
• Make each entry within 60 seconds of
the previous entry.
3
Press the MENU button, then press the
Number 2 button to select VCR SET UP.
Ii SELECTPUSHNO.SHOWN_
1 NORMALPLAY ON [
2 REPEATPLAY [
3 ON SCREEN MODE |
4 LANGUAGE |
5 GUIDECHANNELSET |
6 GUIDECHANNELMAP )
END PUSH EXIT J
4
Press the Number 5 button to select
GUIDE CHANNEL SET.
f GUIDE CHANNELSET
I SELECT GUIDE ell.NO.
GUIDE CI'_::-:_:
USER CH.":'-
END PUSH EXIT
5
Look at the boxes you filled in on
pages 22-23. For stations whose guide
channels and user channels are not the
same, press two Number buttons for
the guide channel and two Number
buttons for the user channel.
• Always enter a "0" before single
digit channels.
• To select line input for the user chan-
nel, press 0, 0. AUX will appear on-
screen.
SELECT USERCH. NO.
GUIDE CH.
USERCH._" _,_
Press the Number 1 button so your
VCR will memorize the guide channel
and user channel numbers you have
selected. Or, press the Number 2 but-
ton to quit and select another pair of
numbers.
_._-- GUIDE CHANNELSET 1
I TO SELECTPUSH NUMBER
GUIDE CH.28
USERCH. 04
1 MEMORIZE
2 SELECTANOTHERCH,
TO CORRECTPUSHCLEAR
k.TO ENDPUSHEXIT
7
Repeat steps 5 and 6 for all the stations
on your list which have different guide
channel and user channel numbers.
8
Press the STATUS/EXIT button to exit.
9
To confirm the guide channel and user
channel numbers you have selected,
press the MENU button to bring up the
main menu display. Then press the
Number 2 button to select VCR SET
UP. Finally, press the Number 6 button
to select GUIDE CHANNEL MAP. A
list of guide channel and user channel
numbers memorized by the VCR will
appear on-screen. If there are more
than 10 pairs of numbers, press the
Number 1 button to view another
screen of numbers. Make sure these
numbers correspond to the boxes you
filled in in step I. Then press the
STATUS/EXIT button to exit.
GUIDE : USERGUIDE: USER I
1 :AUX 2:2 |
3:3 4:4 ]
6:6 7:7 |
g : 9 10:10 /
23:5 91:8 /
TO¢J_3ELPUSH_]
NEXT=I END=EXITJ
+
CHANNEL
(Up/Down)
]---- Buttons
Number Buttons
MENU Button
-- CLEAR Button
STATUS/EXIT
Button
• To correct a guide channel number:
1. Repeat steps 3 - 4 on this page.
2. At step 5, enter the incorrect guide
channel number for both the guide
channel and the user channel. Press
the Number 1 button. Press the STA-
TUS/EXIT button to exit.
3. Repeat steps 3 - 6 again, this time
entering the correct guide channel
and user channel. Press the STA-
TUS/EXIT button to exit.
• To correct a user channel number:
1. Repeat steps 3 - 4 on this page.
2. At step 5, enter the correct guide
channel and user channel numbers.
Press the Number 1 button. Press the
STATUS/EXIT button to exit.
• To cancel a pair of numbers:
1. Follow step 9 to display the guide
channel map.
2. Press the CLEAR button. A pair of
numbers will flash.
3. Press the CHANNEL (Up/Down) but-
tons until the pair of numbers you
wish to cancel isflashing.
4. Press the CLEAR button again. The
pair of numbers that was flashing will
disappear.
5. Press the STATUS/EXIT button to
exit.