Filter
Top Products
6
TV GAME
VIDEO IN
(MONO)
L–AUDIOIN–R
Converter/
Descrambler
A
B
Converter/
Descrambler
A
/
B SwitchSplitter
INOUT
This television has an
extended tuning range and can
tune most cable channels
without using a cable company
supplied converter box. Some
cable companies offer
"premium pay channels" in
which the signal is scrambled.
Descrambling these signals for
normal viewing requires the
use of a descrambler device
which is generally provided by
the cable company.
ANTENNA/CATV CONNECTIONS
Separate VHF/UHF Antennas
Connect the 75 ohm Cable from the VHF antenna and the UHF
antenna Twin-lead to a combiner (not supplied). Attach the Combiner
to the Antenna Jack.
NOTE: If your VHF antenna has a Twin-lead Wire, use the 300-75
ohm Matching Transformer (not supplied), then connect the
Transformer to the Combiner.
For Subscribers to Basic Cable TV Service
For basic cable service not requiring a Converter/Descrambler box,
connect the CATV 75 ohm Coaxial Cable directly to the Antenna
Jack on the back of the television.
For Subscribers to Scrambled Cable TV Service
If you subscribe to a cable service which requires the use of a
Converter/Descrambler box, connect the incoming cable to the
Converter/Descrambler box and connect the output of the box to the
Antenna Jack on the back of the television. Follow the connections
shown left. Set the television to the output of the Converter/
Descrambler box (usually channel 3 or 4) and use the Converter/
Descrambler box to select channels.
For Subscribers to Unscrambled Basic Cable with
Scrambled Premium Channels
If you subscribe to a cable service in which basic cable channels
are unscrambled and premium channels require the use of a
Converter/Descrambler box, you may wish to use a two-set signal
splitter (sometimes called a "two-set coupler") and an A/B Switch
box from the cable installer or an electronics supply store. Follow
the connections shown left. With the switch in the "B" position, you
can directly tune any nonscrambled channels on your TV. With the
switch in the "A" position, tune your TV to the output of the Converter/
Descrambler box (usually channel 3 or 4) and use the box to tune
scrambled channels.
If you connect the TV to VCR, camcorder or TV game, you can
select by pressing the TV/AV button.
Press the TV/AV button repeatedly to select the desired mode.
"AUX1" or "AUX2" will display on the screen for 4 seconds.
AUDIO/VIDEO JACK CONNECTIONS
The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of
each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.
The connection diagrams in the following are offered as suggestions. You may need to modify them to accommodate your particular
assortment of components. The diagrams are intended to show component video and audio interconnections only.
Press the TV/AV selector button to select the AV mode to use the TV as a monitor.
Operate your VCR as usual.
To playback from the camcorder, connect the camcorder to the
TV as shown.
VIDEO IN
(MONO)
L–AUDIOIN–R
3. To connect the TV to the camcorder
Front of TV
To AV OUT jack
The TV can also be used as a display device for many video
games. However, due to the wide variety of different types of signal
generated by these devices and subsequent hook-up variations
required, they have not all been included in the suggested
connection diagrams. You'll need to consult each component's
Owner's Manual for additional information.
2. To connect the TV to a TV Game
1. To connect the TV to a VCR
Rear of TV
VCR
To Audio/Video
OUT
OUT IN
VIDEO
AUDIO
R
L
MONO
300-75 ohm
Matching Transformer
(not supplied)
Combiner
(not supplied)
300-75 ohm
Matching Transformer
(not supplied)
VHF Antenna
Incoming CATV
Single 75 ohm Cable
Combination VHF/UHF Antenna
300 ohm Twin-lead Wire
Splitter
Take off the Splitter
Single 75 ohm Cable
300 ohm Twin-lead Wire
300 ohm Twin-lead Wire
UHF Antenna
VIDEO
AUDIO (L)
AUDIO (R)
TV/AV SELECTION
Combination VHF/UHF Antenna (Single 75 ohm Cable or
300 ohm Twin-lead Wire)
Connect the 75 ohm cable from a combination VHF/UHF antenna to
the Antenna Jack. If your combination antenna has a 300 ohm
Twin-lead Wire, use the 300-75 ohm Matching Transformer (not
supplied).
Combination VHF/UHF Antenna (Separate VHF and UHF
300 ohm Twin-leads)
Connect the UHF Twin-lead Wire to a Combiner (not supplied).
Connect the VHF Twin-lead to the 300-75 ohm Matching
Transformer (not supplied).
Attach the Transformer to the Combiner.
Attach the Combiner to the Antenna Jack.
AUX 1
TV AUX 1 AUX 2
Front of TV
(Not Supplied)
To Audio/Video OUT
(Not supplied)
(Not Supplied)
3G81501A E 12/8/99, 10:12 AM6