Filter
Top Products
Hint
Hint
• To go back one step, press the s button
(during the steps [2] to [7].)
•
Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint
Hint
• If you accidentally select Spanish or
French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
the B button, and select ENGLISH. Finally,
press the CLEAR/C.RESET button.
–
10
–
EN
Setup
2
2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1
1
Turn on the TV and select
channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
POWER
3
3
CH 01
AUTO SET UP
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing
the
K or L button. Then, press the B but-
ton.
3)
Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button.
After scanning, the tuner stops on the low-
est memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2)
Select "LANGUAGE SELECT" by press-
ing the
K or L button. Then, press the B
button.
3)
Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL"
by pressing the K or L but-
ton. Then, press the CLEAR/C.RESET
button.
No
No
Please wait for a few minutes.
After TV station scanning...
• The tuner stops on the lowest memorized
channel.
•You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the
B button once again.
Y
Y
es
es Press the MENU
button to exit
• Refer to “Hint for Cable Box
or Satellite Box” section on
page 6.
Did you connect the cable from the cable box or
the satellite box to the DVD/VCR’s ANT IN jack?
YES
NO
Turn on the unit for the first
time
TV ScreenRemote Control
Clock Set Up
To Select a Channel
You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
VCRVCR
VCR
First Time Use
5
5
4
4
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
6
6
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7
7
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
BPM
Select the current year
Select “AM” or “PM”
8
8 To exit the CLOCK SET
screen.
Select the current hour
Select the current minute
or
or
or
or
or
VCR
VCR
1
1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
2
2
CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
3
3
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
Select the current day
• Select CLOCK SET when
you press the MENU but-
ton. Go to step [2].
VCRVCR
VCR
or
or
or
VCR
VCR
H9602UD(EN)v1.qx3 04.2.20 11:41 PM Page 10