Panasonic AJ-D850A VCR User Manual


 
– 103 –
Specifications
GENERAL
Power supply: AC 120 V, 50 – 60 Hz
Power consumption: 210 W
(Video signals adjustment)
Composite video input signal: ±3 dB
Video output gain: ±3 dB
Video output chroma gain: ±3 dB
Video output hue: ±30°
Video output setup: ±15 IRE
Video output sync phase: ±15 µsec
Video output SC phase: ±180°
Video output Y/C delay: ±300 nsec
AUDIO
(Digital audio)
Sampling frequencies: 48 kHz
Quantizing: 16 bits
Frequency response: 20 Hz to 20 kHz ±1 dB
Dynamic range: Better than 90 dB (1 kHz, emphasis OFF,
“A” weighted)
Distortion: Less than 0.05% (1 kHz, emphasis OFF,
standard level)
Crosstalk: Less than –80 dB (1 kHz, between
2 channels)
Wow & flutter: Below measurable limit
Headroom: 20 dB
Emphasis: T1=50 µsec/T2=15 µsec (on/off
selectable)
(Cue track)
Frequency response: 300 Hz to 6 kHz ±3 dB
(Audio input connector)
Analog input (CH1/CH2): XLR×2, 600/high impedance selectable,
+4/0/–20 dBu
Digital input (CH1/CH2): XLR×1, AES/EBU format
Serial digital input (option): Complies with SMPTE 259M-C, 272M
standard (BNC, 75)
Cue track input: XLR×1, 600/high impedance selectable,
+4/0/–20/–60 dBu
(Audio output connector)
Analog output (CH1/CH2): XLR×2, low impedance, +4/0/–20 dBu
Digital output (CH1/CH2): XLR×1, AES/EBU format
Serial digital output (option): Complies with SMPTE 259M-C, 272M
standard (BNC, 75)
Cue track output: XLR×1, low impedance, +4/0/–20 dBu
Monitor output: XLR×2, low impedance, +4/0/–20 dBu
Headphones: Variable level, mini-jack, 8
Other input/output connector
Time code input: XLR×1, 0.5 to 8 Vp-p
Time code output: XLR×1, 2.0 Vp-p
RS-422A input/output: D-sub 9-pin, RS-422A interface
RS-422A output: D-sub 9-pin, RS-422A interface
RS-232C: D-sub 25-pin, RS-232C interface
Parallel input/output: D-sub 25-pin
Encoder remote: D-sub 15-pin
Weight and dimensions shown are approximately.
Specifications are subject to change without notice.
Operating ambient temperature: 41°F to 104°F (5°C to 40°C)
Operating ambient humidity: 10% to 90% (no condensation)
Weight: 36.96 lbs (16.8 kg)
Dimensions (W × H × D): 16-3/4 × 6-15/16 × 16-3/8 inches
Recording format: DVCPRO format
Recording tracks: Digital video
Time code; Recorded in sub-code area
Digital audio; 2 channels
Cue Signal; 1 track
Control (CTL);1 track
Tape speed: 33.820 mm/sec
Recording time: 184 minutes (with AJ-5P92LP)
66 minutes (with AJ-P66MP)
Tape: 1/4-inch thin magnetic layer metal tape
FF/REW time: Less than 3 minutes (with AJ-5P92LP)
Less than 2 minutes (with AJ-P66MP)
Editing accuracy: ±0 frame (using time code)
Tape timer accuracy: ±1 frame (using continuous CTL signal)
Servo lock time: Less than 0.5 sec.
(color framing/ standby ON)
VIDEO
(Digital video)
Sampling frequencies: Y; 13.5 MHz/PB, PR; 3.375 MHz
Quantizing: 8 bits
Error correction: Reed-Solomon product code
(Digital IN/analog component OUT)
Video bandwidth: Y; 30 Hz to 5.5 MHz (±0.5 dB)
5.75 MHz (–2 dB)
P
B, PR; 30 Hz to 1.3 MHz (±1 dB)
1.5 MHz (–5 dB) typ.
S/N ratio: Better than 60 dB
K factor: Less than 1%
(Analog component IN/component OUT)
Video bandwidth: Y; 30 Hz to 5.5 MHz (±1 dB)
5.75 MHz (–3 dB)
P
B, PR; 30 Hz to 1.3 MHz (±1 dB)
1.5 MHz (–6 dB) typ.
S/N ratio: Better than 55 dB
K factor: Less than 1%
(Analog composite IN/composite OUT)
Video bandwidth: Y; 30 Hz to 4.5 MHz (±1 dB)
DG: Less than 4%
DP: Less than 3°
Y/C delay: Better than 20 nsec
K factor: Less than 2%
(Video input connector)
Analog component input: BNC×3 (Y, PB, PR)
Y; 1.0 Vp-p, 75
P
B, PR; 0.486/0.7 Vp-p switchable, 75
(75% color bar, 7.5% setup)
Analog composite input: BNC×2, loop-through, 75 on/off
Reference input: Analog composite
BNC×2, loop-through, 75 on/off
Serial digital component input
(option): Complies with SMPTE 259M-C standard,
BNC×2, active through
(Video output connector)
Analog component output: BNC×3 (Y, PB, PR)
Y; 1.0 Vp-p, 75
P
B, PR; 0.486/0.7 Vp-p switchable, 75
(75% color bar, 7.5% setup)
Analog composite output: BNC×3
Video1/video2/video3 (superimpose
on/off)
Serial digital component output
(option): Complies with SMPTE 259M-C standard,
BNC×3