Filter
Top Products
For accentuating the horizontal contours
during down-conversion and line conversion
(1080i
<>
720p).
0000 0dB
0001
i
0.7dB
0002
i
1dB
0003
i
1. 2dB
0004
i
1.5dB
0005
i
2dB
93
Setup menus
The underlining (__) denotes the factory setting mode.
<VIDEO>
No./Item Description of setting No./Item Description of setting
601*
1
VIDEO INT SG
For selecting the type of internal signal.
0000
100
%
CB
:
A 100% color bar signal is selected.
0001 75
%
CB
:
A 75% color bar signal is selected.
0002 SMPTE
:
An SMPTE color bar signal is selected.
0003 ARIB
:
An ARIB color bar signal is selected.
0004 MB
:
A multiburst signal is selected.
0005 RAMP
:
A ramp signal is selected.
0006 BLACK
:
A black signal is selected.
0007 PLL
:
A PLL signal is selected.
0008 EQ
:
An EQ signal is selected.
600*
1
VIDEO IN SEL
For selecting the video signal which is to be input.
0000 INT SG
:
The internal signal selected by the VIDEO INT
SG item is generated.
0001 HDSDI
:
The serial video signal which has been input to the
HD SDI IN connector is selected.
0002 SDTI
:
(In 59/60 Hz mode)
The compressed IF signal which has been input to
the SDTI IN connector is selected. (This setting
does not appear when the AJ-YAC15P optional
board has not been installed.)
0002 SD SDI
:
The serial video signal which has been input to the
SD SDI IN connector is selected. (This setting does
not appear when the AJ-UC1700G optional board
has not been installed.)
602*
1
SDI IN MODE
For selecting how to process the serial input.
0000 DR OFF
:
The 8 higher bits after rounding up
the 2 lowest bits are recorded.
0001 DR ON
:
The signal with 8 higher bits, obtained
by dynamic rounding, is recorded.
603
V-MUTE SEL
For selecting whether to mute the video output
signals if LOW RF has been detected during
playback.
0000 N MUTE
: The signals are not muted.
(They are frozen.)
0001 GRAY
:
The signals are muted with gray.
0002 BLACK
:
The signals are muted with black.
0003 NOISE
:
The signals are muted with noise.
606
SD MONI O
SEL
For selecting the SD SDI or MONITOR output
signal.
0000 MONI
: : The MONITOR signal is output.
0001 SDI
: The same video signal as the
one output from the SD SDI
OUT1 connector is output
<Note>
When 1 (SDI) is selected, the time code and other
information are not superimposed on the display.
604*
1
FREEZE SEL
For selecting the freeze mode of the still
pictures and slow playback mode.
0000 FIELD
: Field freeze, field slow
0000 FRAME
: Frame freeze, frame slow
605*
1
INTERPOLATE
During field slow playback, vertical interpolation is
conducted automatically to minimize the up/down
movement of the playback pictures. However, this
setting enables the interpolation operation to be
forcibly set to OFF.
0000 OFF
:
The interpolation is forcibly set to OFF.
0001 AUTO
:
During slow playback, the interpolation
is automatically set to ON.
620*
4
DOWNCON
MODE
For selecting the picture frame during down-
conversion.
0000 FIT_V
: Side cut mode
0001 FIT_H
: Letter box mode
0002 FIT_HV
: Squeeze mode
0003 14:9
: Semi letter box 14:9
0004 13:9
: Semi letter box 13:9
621*
5
UPCON MODE
For selecting the picture frame during up-
conversion.
0000 FIT_V
: Side panel mode
0001 FIT_H
: Top and bottom cut in vertical
direction
0002 FIT_HV
: Stretch mode
622
D/C RESP
H
For selecting the horizontal frequency band
during down-conversion and line conversion
(1080i
<>
720p).
0000
WIDE
0001 STD
623
D/C RESP
V
For selecting the vertical frequency band
during down-conversion and line conversion
(1080i
<>
720p).
0000 WIDE
0001 STD
624*
5
U/C RESP
H
For selecting the horizontal frequency band
during up-conversion and line conversion.
0000
STD
0001
NARROW
625*
5
U/C RESP
V
For selecting the vertical frequency band
during up-conversion and line conversion.
0000 STD
0001
NARROW
626
D/C ENH
H
<Note>
The numbers on the superimposed
display are approximations only.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode
has been selected as the system menu item.
*4: This item is not displayed when the 23/24 Hz or 25 Hz (HD) mode has
been selected as the system menu item No.25 (SYSTEM FREQ) setting.
*5: This item is not displayed when the 25 Hz (HD or SD) mode has been
selected as the system menu item No.25 (SYSTEM FREQ) setting.