13
EN
General information
Use a TIMER programming to automatically start
and stop a recording at a later time or date.The
TV-Video Combi will switch to the right pro-
gramme number and begin recording at the cor-
rect time.With this TV-Video Combi, you can
pre-programme up to eight recordings within a
period of one year.To make a programmed
recording, your TV-Video Combi needs to know:
*the date you want to make the recording
*the programme number of the TV channel
*the start and stop time of the recording
*VPS or PDC on or off
This information is saved in a TIMER block.
Programming a recording with the
'SHOWVIEW®' system
Thanks to this simplifed programming system, you
no longer need to tediously enter the date, pro-
gramme number, start and end time. All the infor-
mation needed for programming is contained in the
SHOWVIEW-programming number.You can find this
SHOWVIEW number in most TV listing magazines
written next to the concerned programme.
1.
1.Press on the remote control.
2.
2.Enter the entire SHOWVIEW number.This num-
ber is up to 9 digits long and can be found
next to the start time of the TV programme in
your TV listing magazine. [e.g:1-234-5 or 1
234 5] If you make a mistake, you can clear
your input with .
3.
3.Press .
4.
4.Select ONCE, DAILY, or WEEKLY recording
with .Then press .
5.
5.
The decoded data appears after confirmation.You
can go back to change the data. Select the corre-
sponding input field using
or
. Change the data with .
6.
6.When all inputs are correct, press
.The programming information is
stored in a TIMER block.
STATUS/EXIT
0..9
CLEAR
FWD 1- B
FWD 1- BSTOP C-LPLAY B-K
SV/V+
CLEAR
SV/V+
7. Programming a recording (TIMER)
What is 'VPS/PDC'?
'VPS' (Video Programming System)/ 'PDC'
(Programme Delivery Control) are used to con-
trol the start and duration of TV channel record-
ings. If a TV programme starts earlier or ends
later than scheduled, the TV-Video Combi will
turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
Usually the VPS or PDC time is the same as
the start time. But if your TV guide shows a
VPS or PDC time which is different from the
programme’s scheduled start time, e.g. 20.10
(VPS/PDC 20.14), you must enter the VPS/PDC
time exact to the minute. If you want a start time
different from the VPS/PDC time, you must
switch VPS/PDC off.
ShowView system
ShowView No.
1 2 3 – – – – – –
SET=SV/V+
CORRECT=CLEAR
END=EXIT
ShowView system
→ONCE
DAILY
WEEKLY
SELECT KL CHOOSE B
END=EXIT
Selecting once/daily/weekly recordings
Using , select from the fol-
lowing options:
'ONCE': Recording once
'DAILY': Repeated daily recordings (Monday
to Friday)
'WEEKLY.': Repeated weekly recordings (every
week on the same day)
STOP C-LPLAY B-K
Prog No changes to ' - - '
* The entered SHOWVIEW number is incorrect.
Correct your input or end with
.
The following message appears on the
screen:'ERROR'
* The entered SHOWVIEW number is incorrect. Correct
your inputs or end with .
* Check the time/date (see chapter 'Installing your
TV-Video Combi', section 'Setting the clock').
* A daily recording was entered for the wrong
day. Daily programming can only be used for
recordings to be made from Monday to Friday.
The following message appears on the
screen:’TIMER NOT COMPLETED’
* The channel is wrong.
STATUS/EXIT
STATUS/EXIT
T6400EZ-BG/DK(EN).qx3 03.4.21 15:51 Page 13