Roland GR-33 Universal Remote User Manual


 
59
Chapter 6 Using the Built-in Effects
Chap.
6
PAN (Output pan) L64–0–R63
Specify the stereo location of the output sound.
A setting of L64 is far left, 0 is center, and R63 is far right.
POST GAIN 0/+6/+12/+18 dB
Specify the level of the output sound.
LOW GAIN -15–+15 dB
Specify the gain (amount of boost or cut) for the low
frequency range.
Positive (+) settings will emphasize (boost) the low
frequency range.
HIGH GAIN -15–+15 dB
Specify the gain (amount of boost or cut) for the high
frequency range.
Positive (+) settings will emphasize (boost) the high
frequency range.
LEVEL (Output level) 0–127 #
Specify the output volume.
11: HEXA-CHORUS
Hexa-chorus is a six-stage chorus which adds depth and
spaciousness to the sound. (Six chorus sounds with different
delay times are overlaid.)
fig.6-15
PRE DELAY (Pre delay time) 0.0–100 ms
Specify the delay time from the original sound until when
the chorus sound is heard.
RATE 0.05–10.0 Hz #
Specify the modulation frequency of the chorus sound.
DEPTH 0–127
Specify the modulation depth of the chorus sound.
PRE DLY DEV (Pre delay deviation) 0–20
The Pre Delay parameter explained above specified the delay
time from the original sound until when the chorus sound is
heard. This Pre Delay Deviation parameter specifies the
differences in Pre Delay time for each of the chorus sounds.
Higher settings will cause each of the chorus sounds to be
spread further apart.
DEPTH DEV (Depth deviation) -20–+20
Specify the difference in modulation depth between each of
the chorus sounds.
PAN DEV (Pan deviation) 0–20
Specify the difference in stereo position between each of the
chorus sounds.
With a setting of 0, all of the chorus sounds will be panned to
the center. Setting this to 20 provides the greatest breadth.
BALANCE (Effect balance) D100:0E–D0:100E
Specify the volume balance between the original sound and
the chorus sound.
With a setting of D100:0E only the original sound will be
output, and with a setting of D0:100E only the chorus sound
will be output.
LEVEL (Output level) 0–127
Specify the output volume.
12: TREMOLO-CHO (Tremolo Chorus)
Tremolo-chorus is a chorus with a tremolo effect (cyclic
modulation of volume).
fig.6-16
PRE DELAY (Pre delay time) 0.0–100 ms
Specify the delay time from the original sound until when
the chorus sound is heard.
CHORUS RATE 0.05–10.0 Hz
Specify the modulation frequency of the chorus sound.
CHORUS DEPTH 0–127
Specify the modulation depth of the chorus sound.
TREM RATE (Tremolo rate) 0.05–10.0 Hz #
Specify the modulation frequency of the tremolo effect.
TREM SEP (Tremolo separation) 0–127
Specify the spaciousness of the tremolo effect.
TREM PHASE (Tremolo phase) 0–180
Adjusts the phase of the tremolo effect.
BALANCE (Effect balance) D100:0E–D0:100E
Specify the volume balance between the original sound and
the tremolo-chorus sound.
With a setting of D100:0E only the original sound will be
output, and with a setting of D0:100E only the tremolo-
chorus sound will be output.
LEVEL (Output level) 0–127
Specify the output volume.
Balance E
Balance E
L in
R in
L out
R out
Hexa Chorus
Balance D
Balance D
Tremolo Chorus
L in
R in
L out
R out
Balance D
Balance D
Balance E
Balance E