Roland GR-33 Universal Remote User Manual


 
61
Chapter 6 Using the Built-in Effects
Chap.
6
15: STEREO-FL (Stereo Flanger)
This is a stereo flanger (the LFO has the same phase for left
and right). This produces a metallic resonance reminiscent of
a jet airplane taking off and landing. A filter is provided so
that you can adjust the tone of the flanger sound.
fig.6-19
FILTER TYPE Off/LPF/HPF
Specify the type of filter.
Off:
A filter will not be used.
LPF:
Cut the frequency region above the Cutoff Freq setting.
HPF:
Cut the frequency region below the Cutoff Freq setting.
CUTOFF FREQ (Cutoff frequency)
200/250/315/400/500/630/800/1000/1250/1600/2000/2500/3150/
4000/5000/6300/8000 (200–8000 Hz)
Specify the frequency at which the filter will begin cutting.
PRE DELAY (Pre delay time) 0.0–100 ms
Specify the time delay from the original sound until the
flanger sound is heard.
RATE (LFO rate) 0.05–10.0 Hz #
Specify the modulation frequency of the flanger sound.
DEPTH (LFO depth) 0–127
Specify the modulation depth of the flanger sound.
PHASE 0–180
Specify the spaciousness of the flanger sound.
FEEDBACK -98–+98 %
Specify the proportion (%) of the flanger sound that is to be
returned to the input.
Positive (+) settings will return the signal to the input with
the original phase, while negative (-) settings produce an
inverted phase.
Higher settings will produce a more distinctive sound.
LOW GAIN -15–+15 dB
Specify the gain (amount of boost or cut) for the low
frequency range.
Positive (+) settings will emphasize (boost) the low
frequency range.
HIGH GAIN -15–+15 dB
Specify the gain (amount of boost or cut) for the high
frequency range.
Positive (+) settings will emphasize (boost) the high
frequency range.
BALANCE (Effect balance) D100:0E–D0:100E
Specify the volume balance between the original sound and
the flanger sound.
With a setting of D100:0E only the original sound will be
output, and with a setting of D0:100E only the flanger sound
will be output.
LEVEL (Output level) 0–127
Specify the output volume.
16: STEP-FL (Step Flanger)
Step flanger is a flanger in which the pitch of the flanger
sound changes in steps. The frequency of the pitch change
can be specified as a note length of a specific tempo.
fig.6-20
PRE DELAY (Pre delay time) 0.0–100 ms
Specify the time delay from the original sound until the
flanger sound is heard.
RATE 0.05–10.0 Hz
Specify the modulation frequency of the flanger sound.
DEPTH 0–127
Specify the modulation depth of the flanger sound.
FEEDBACK -98–+98 %
Specify the proportion (%) of the flanger sound that is to be
returned to the input.
Positive (+) settings will return the signal to the input with
the original phase, while negative (-) settings produce an
inverted phase.
Higher settings will produce a more distinctive sound.
STEP RATE 0.05–10.0 Hz #
Specify the frequency of pitch change.
PHASE 0–180
Specify the spaciousness of the flanger sound.
R in R out
L in L out
Flanger
Feedback
Feedback
Flanger
Balance E
Balance D
Balance E
Balance D
2-Band
EQ
2-Band
EQ
R in R out
L in L out
Feedback
Feedback
Balance E
Balance D
Balance E
Balance D
2-Band
EQ
2-Band
EQ
Step Flanger
Step Flanger