Filter
Top Products
Watching TV
1 Insert the batteries into the remote control unit.
(See page 9.)
2 Connect the antenna cable to the TV/DVD. (See
page 13.)
3 Plug in the AC cord to the AC outlet. (See page 8.)
Method 2
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CATV/DIGITAL.
To selecta I or2-digitchannelnumber(e. g.,Channel 5):
Press 5
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection wi!! be made
ifthere is no operation within a few seconds.
Press POWER on the TV/DVD, or POWER on the
remote control.
TV status indicator (POWER)
ON Lighting (Green)
OFF/Standby Lighting (Red)
• POWER indicator (Green): The TV/DVDS is on. ("Please
wait" will appear for a few seconds on the screen.)
Press TV/DVD to select the TV mode.
To selecta3-digitchannelnumber (e. g., Channel 115):
Press 1_1_5
To selecta4-digit channelnumber(e. g., Channel 22.1):
Press 2-->2-->°(DOT) -->1
• When you enter 0-9 only, channel selection wi!! be made
ifthere is no operation within a few seconds.
• If you press 0 by itself in "Air" reception, nothing wil!
happen.
Complete the above steps within a few seconds.
When you enter 0-9 and • (DOT), channel selection will
be made ifthere is no operation within a few seconds.
• The LANGUAGE setup menu will appear automatically
when TV MENU is pressed on for the first time.
Press POWER on the TV/DVD, or POWER on the
remote control.
• The TV enters standby mode and the image on the screen
disappears.
• The POWER indicator on the TV/DVD changes to Red.
Auto Ch Memory makes the TV/DVD look for all
channels viewable in the set area.
1 Press TV MENU and the MENU screen displays.
3
4
• Ifyou are not going to use this TV/DVD for a long period of 5
time, be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when POWER
is turned off. 6
You can change channels in several ways.
Method 1
Using CH ^/v on the remote control unit or on the
TV/DVD.
• Ifyour cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although it may appear as though
the channel does not change, it actually moves from the
analog to the digital channel in sequence.
Ifyou use channel-down, it will move in reverse, from the
digital channel to the analog channel.
Press A/T to select "Channel", then press _ or ENTER.
Press A/T to select "Auto Ch Memory", then press _ or
ENTER.
Press A/T to select "Signal Type".
Press ,/_ to select "Air" or "Cable".
Air VHF/UHF channels
Cab e CABLE TV channe s
Press A/T to select "Automatic Search", then press
ENTER.
The TV will begin memorizing all the channels available
in your area.
• It may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a BAR display
may not advance for several minutes, please be
patient.
• Memorizing channels is best accomplished during
evening "PRIMETtME" hours, as more stations are
broadcasting digital signals. Memorizing channels can
only be accomplished while a station is broadcasting a
digital signal to set that channel into memory.
• New digital channels may be added to your area
periodically, itis recommended to perform the "Automatic
Search" procedure regularly.
_-15
50Q0131A E.indb 15 (#.b_ 3/3/2008 1:43:27PM