Sony BR8K-MF1 TV Cables User Manual

For the customers in Europe, Australia and New Zealand
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is
Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany. For any service or guarantee matters
please refer to the addresses given in separate service or
guarantee documents.
This apparatus shall not be used in the residential area.
Laser Diode Properties
Wavelength : 850 nm
Emission duration : Continuous
Laser output power : 0.56 mW
Laserdiode data
Bølgelængde: 850 nm
Strålingsvarighed: Kontinuerlig
Lasereffekt: 0,56 mW
Laserdiodens egenskaper
Våglängd: 850 nm
Strålningstid: utan avbrott
Laseruteffekt: 0,56 mW
Laserdiodens egenskaper
Bølgelengde: 850 nm
Emisjonslengde: Kontinuerlig
Laser utgangseffekt: 0,56 mW
The use of optical instruments with this product will increase
eye hazard.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Operating or storing the card in the following locations may cause
damage to the card:
Extremely hot or cold places (Operating temperature: 0 °C to 40 °C
[32 °F to 104 °F])
Exposed in direct sunlight for a long time, or close to heating
equipment (e.g., near heaters)
Close to sources of strong magnetism
•Close to sources of powerful electromagnetic radiation, such as
radios or TV transmitters
Locations subject to strong vibration or shock
Optical fiber connector LC duplex Fiber connector (1)
Laser unit Multi-mode 850 nm SFP Transceiver,
conforming to SFP MSA
Audio line input Phono jack, right (1)/left (1)
Maximum input level: 2.8 Vrms
Power supply 12 V DC (supplied from the camera)
Power consumption 3.0 W max.
Operating temperature 0 °C to 40 °C (32 °F to 104 °F)
Operating humidity 20 % to 80 % (no condensation)
Storage temperature – 20 °C to + 60 °C (–4 °F to +140 °F)
Storage humidity 20 % to 95 % (no condensation)
134 × 25.6 × 74.6 mm (w/h/d) (5
× 1
3 inches) (not including the projected parts)
Mass Approx. 125 g (4 oz)
Supplied accessories Operating Instructions (1)
Design and specifications are subject to change without notice.
3-287-516-01 (1)
HD Optical Multiplex
Operating Instructions
Mode d’emploi
Manual de instrucciones
Sony Corporation 2007 Printed in Japan
The BRBK-MF1 interface card is designed for exclusive use with the
Sony BRC-Z700 HD 3CMOS Color Video Camera.
The combined use of this card, CCFC-M100HG Optical Fiber Cable
and BRU-H700 HD Optical Multiplex Unit allows up to 1,000 m
(3,281 feet) transmission of camera images, external video sync
signals and control signals via one cable.
For installation of the interface card and for operations after it is
installed, refer to the Operating Instructions supplied with the HD
camera or HD Optical Multiplex Unit.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-