Filter
Top Products
62
Menu Contents
Chapter 6 Menu Setting
LOCAL ENABLE [> Local ENA]: Select which of the recording/
playback control buttons (PREV, PLAY, NEXT, STOP, and REC)
operate when the control mode selector is set to “REMOTE.”
ALL DISABLE [>> All DIS]: All of the recrding/playback
control buttons are disabled.
*STOP [>> STOP]: Only the STOP button is enabled.
ALL ENABLE [>> All ENA]: All of the recording/playback
control buttons are enabled, and settings such as
preroll time change or time data display selection are
effective.
REC MODE [>REC mode]: Select the recording mode. *NORMAL REC [>>Normal]: Normal recording.
PRE ALARM REC [>>Pre Alarm]: Pre-alarm recording.
CONT. REC [>>Cont. REC]: Continuous recording.
INTERVAL REC [>>Interval]: Interval recording (settings
required in next item, INTERVAL REC).
INTERVAL REC [>Interval
REC]:
Set the standby and
recording intervals for
interval recording.
INTERVAL [>>Int Time]: Set
the standby interval for
interval recording.
*30 sec [>>>30 SEC]: 30 seconds
1 min [>>>1 MIN]: 1 minute.
5 min [>>>5 MIN]: 5 minutes.
10 min [>>>10 MIN]: 10 minutes.
REC TIME [>>Rec Time]: Set
the recording interval for
interval recording.
*0.5 sec [>>>0.5SEC]: 0.5 seconds.
1.0 sec [>>>1.0SEC]: 1.0 second.
1.5 sec [>>>1.5SEC]: 1.5 seconds.
2.0 sec [>>>2.0SEC]: 2.0 seconds.
REC INHIBIT [> REC INH]: Determine whether to prohibit
recording.
*OFF [>> OFF]: Do not prohibit recording.
ON [>> ON]: Prohibit recording. (The REC INHI indicator
in the display section lights.)
SEARCH ENABLE [> Search ENA]: Select how the unit enters the
search mode.
*DIAL DIRECT [>> DIAL]: Press the SEARCH button or,
except during recording, turn the search dial.
VIA SEARCH KEY [>> via KEY]: Press the SEARCH
button.
MAX SRCH SPEED [> Max
SRCH]:
Specify the maximum
search speed in search
(shuttle) mode and F. FWD
(fast forward)/REW (rewind)
mode.
SHUTTLE [>> SHUTTLE]:
Specify the maximum
search speed in shuttle
mode.
X60 [>>> X60]: Maximum 60 times normal speed
*X32 [>>> X32]: Maximum 32 times normal speed
X16 [>>> X16]: Maximum 16 times normal speed
F. FWD/REW [>> F. FWD/
REW]:
Specify the maximum
search speed in F. FWD/
REW mode.
a)
MAX [>>> MAX]: No maximum search speed is specified.
*X85 [>>> X85]: Maximum 85 times normal speed
X60 [>>> X60]: Maximum 60 times normal speed
X32 [>>> X32]: Maximum 32 times normal speed
Note
When this item is set to MAX, the playback video signal is
muted.
JOG RESPONSE [>JOG dial]:
Set the search speed
corresponding to number of
search dial rotations in jog
mode.
TYPE1 [>>type 1]: Search speed varies linearly over the
range -1 to +1 times normal speed.
TYPE2 [>>type 2]: Search speed varies in stepwise
manner over the range –3 to +3, as shown in
“TYPE2”
b)
in figure below. (In the ±1 speed section,
speed does not vary, regardless of search dial
rotations.)
TYPE3 [>>type 3]: Search speed varies linearly over the
range –3 to +3, as shown in “TYPE3”
c)
in figure
below.
PREROLL TIME [> Preroll]:
Set the preroll time.
15 SEC [>> 15 sec] to 0 SEC [>> 0 sec]: The preroll time
can be set in one-second increments to between 0
and 15 seconds.
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit
such as the PVE-500 has been connected, this setting is
disabled and the setting on the editing control unit is in
effect. Operations such as the preroll time setting and the
time data switching operation are also performed on the
editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
following cue-up.
*STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
OPERATIONAL FUNCTION [Operational]: Operation settings Description of settings