Sony E50A10 CRT Television User Manual


 
KDF-E42A10
KDF-E50A10
Sony Corporation © 2005 Printed in U.S.A.
2-597-545-11(1)
Quick Setup Guide
Connecting Your TV
(See reverse side)
Programming
the Remote Control
Running Initial Setup
For further information, see the operating instruction supplied with the TV.
Please retain this guide for your future reference.
Please follow the steps to setup your TV:
zzz
For service and technical assistance, call our Customer Information Service Center (Toll Free):
US residents: 1-800-222-SONY (7669) or visit http://www.sonystyle.com/tv/
Canadian residents: 1-877-899-SONY (7669) or visit http://www.sonystyle.ca/tv/
DO NOT RETURN TO THE STORE
2
1
3
zzz
Projection Lamp: Periodic replacement of the projection lamp
will maintain the picture quality.
See Replacement Lamp section of the manual.
Wide Mode: Selecting appropriate screen mode will increase
enjoyment of your TV viewing.
When watching a Standard Definition source (4:3 aspect
ratio) on this TV, you will see bars on both the left and right
sides of the screen. Press the WIDE button on your remote to
cycle through different screen modes to fill the screen in
various ways. (Wide Zoom enlarges the center, Normal is
how your TV receives the signal, Full stretches horizontally
and Zoom enlarges the image proportionately to fill the
screen.)
When watching a High Definition source (16:9 aspect ratio)
on this TV, you will see screen filled with a image. Press the
WIDE button on your remote to toggle through different
screen modes, especially zooming in to the center of the
screen. (Wide Zoom enlarges the center, Full displays the
image at its original size, Zoom enlarges the image
proportionately to fill the screen.)
When the TV receives a 720p or 1080i formatted signal, the
Normal mode is not available. See Using WIDE Button section
of the manual.
If you feel the images on the screen is stretched, press the WIDE button to select a
different screen mode.
Notes on your new TV
Running Initial Setup
1 Press to turn on the TV.
The Initial Setup screen appears.
2 Press V or v to highlight the on-screen
display language. Then press .
The message “First please connect
cable and/or antenna” appears. This may require 50+ minutes for
completion and “Start auto program now?” appears.
3 Press (Yes) to start Initial Setup.
Initial Setup automatically creates a list of
receivable channels from both VHF/UHF
antenna and cable TV channels if both
sources are connected.
When Initial Setup is complete, the TV
will display the total number of analog channels and the total
number of digital channels found.
4 Press to exit this screen.
To run Auto Program again at a later time
Refer to the manual on “Initial Setup” and “Auto Program” sections.
2
Best Audio/Video
Performance
Activating CableCARD™ Service
Before you can use CableCARD service, you need to insert the
CableCARD device (supplied by your cable provider) and activate
the service.
Inserting the CableCARD incorrectly may result in permanent damage to the card and
the TV.
The connection diagrams shown in the reverse side are recommendations only; other
possible solutions may exist. Connections that include an AV receiver can often be
complex, so check your AV receiver’s
instruction manual for additional
details.
See the “Cables Required” chart that
appears with the diagram to determine
which cables you’ll need. Depending on
the components you plan to connect,
you may need to purchase extra cables.
1
Connecting Your TV
Programming the Remote Control
The remote control is preset to operate Sony brand video equipment.
Sony Equipment Programmable Code Number
DVR 772
DVD/VCR 601 (Sony Dream System)
SAT/CABLE 801 (Sony Satellite Receiver)
Follow the steps below to program your TV’s remote control to
operate the non-Sony video equipment.
Find the three-digit code for your equipment from the
“Manufacturer’s Codes” listed on right. If more than one code
number is listed, try entering from the code listed first.
1 Press and hold the , or FUNCTION
button you want to program on the remote control and
press the
button simultaneously.
The selected FUNCTION button (
, or )
will flash.
2 Enter the three-digit manufacturer’s code number
using the 0-9 buttons while the button is lit. If code is
not entered within 10 seconds, you must perform the
step 1 again.
3 Press button.
When programmed correctly, the selected FUNCTION
button will flash twice, and when not, it flashes five
times.
To check if the code works
Aim your TV’s remote control at the equipment, and press
the green
button. If the equipment responds, the
programming is completed. If not, try the next code listed.
3
If no code is input within the above specified time, or an invalid or incorrect code
number is input, the remote control automatically goes back to the previous setting.
In some cases, you may not be able to program your remote control to operate other
equipment. In such cases, use the equipment’s own remote control.
Removing the batteries or dead batteries may cause the programmed codes to be lost
and revert back to the factory setting. Reprogramming the codes may be necessary.
1
2
3
1
Manufacturer’s codes
DVD Players
Manufacturer Code
Sony 751
General Electric 755
Hitachi 758
JVC 756
Magnavox 757
Mitsubishi 761
Panasonic 753
Philips 757
Pioneer 752, 778
RCA/PROSCAN 755
Samsung 758
Toshiba 754
Zenith 760
DVD Changers
Manufacturer Code
Sony 765
Panasonic 766
DVD/VCR Combo Units
Manufacturer Code
Sony 767
Broksonic 776
JVC 775
Panasonic 777
Samsung 774
Toshiba 773
Zenith 768
HDD/DVD Combo Units
Manufacturer Code
Sony 772, 771, 770
5.1ch DVD AV System
Manufacturer Code
Sony (DAV) 601, 602, 603, 604
AV Receivers
Manufacturer Code
Sony 764
VCRs
Manufacturer Code
Sony 301, 302, 303
Admiral (M. Ward) 327
Aiwa* 338, 344
Audio Dynamic 314, 337
Manufacturer Code
Broksonic 319, 317
Canon 309, 308
Citizen 332
Craig 302, 332
Curtis Mathes 304, 338, 309
Daewoo 341, 312, 309
DBX 314, 336, 337
Dimensia 304
Emerson 319, 320, 316, 317,
318, 341
Fisher 330, 335
Funai 338
General Electric 329, 304, 309
Go Video 322, 339, 340
Goldstar 332
Hitachi 306, 304, 305, 338
Instant Replay 309, 308
JC Penney 309, 305, 304, 330,
314, 336, 337
JVC 314, 336, 337, 345,
346, 347
Kenwood 314, 336, 332, 337
LG 332
LXI (SEARS) 332, 305, 330, 335,
338
Magnavox 308, 309, 310
Marantz 314, 336, 337
Marta 332
Memorex 309, 335
Minolta 305, 304
Mitsubishi/MGA 323, 324, 325, 326
Multitech 325, 338, 321
NEC 314, 336, 337
Olympic 309, 308
Optimus 327
Orion 317
Panasonic 308, 309, 306, 307
Pentax 305, 304
Philco 308, 309
Philips 308, 309, 310
Pioneer 308
Quasar 308, 309, 306
RCA/PROSCAN 304, 305, 308, 309,
311, 312, 313, 310,
329
Realistic 309, 330, 328, 335,
324, 338
Sansui 314
Samsung 322, 313, 321
Sanyo 330, 335
Scott 312, 313, 321, 335,
323, 324, 325, 326
Sharp 327, 328
Signature 2000 (M.Ward)
338, 327
SV 2000 338
Manufacturer Code
Sylvania 308, 309, 338, 310
Symphonic 338
Tashiro 332
Tatung 314, 336, 337
Teac 314, 336, 338, 337
Technics 309, 308
Toshiba 312, 311
Wards 327, 328, 335, 331,
332
Yamaha 314, 330, 336, 337
Zenith 331
Cable Boxes
Manufacturer Code
Sony 230
Hamlin/Regal 222, 223, 224, 225,
226
Jerrold/ 201, 202, 203, 204,
General Inst./ 205, 206, 207, 208,
Motorola 218, 222
Oak 227, 228, 229
Panasonic 219, 220, 221
Pioneer 211, 214, 215
Scientific Atlanta 209, 210, 211
Tocom 216, 217
Zenith 212, 213
Satellite Receivers
Manufacturer Code
Sony 801
Dish Network 810
Echostar 810
General Electric 802
Hitachi 805
Hughes 804
Mitsubishi 809
Panasonic 803
Philips 811
RCA/PROSCAN 802, 808
Toshiba 806, 807
Samsung 812
* If an Aiwa VCR does not
work even though you enter
the code for Aiwa, enter the
code for Sony instead.
Making Audio/Video Connections
Your new TV includes various types of video inputs and two types
of audio jacks; composite-RCA type and digital audio (optical).
Use the outputs/inputs that are available on your components that
provide the best video/audio performances:
Connector type
HDMI
(High-Definition Multimedia
Interface)
DVI (Digital Video Interface)
Will require an adapter to connect to this TV.
Component video
S VIDEO
Composite video
RF/Coaxial
Review the following chart to determine which diagram to use to connect the components in your system:
Turn off and unplug all components before making connections.
Connector type
Digital Optical
Digital Coaxial
Will require an adapter
to connect to this TV’s
digital audio input.
Analog Audio
PCM/DOLBY DIGITAL
DIGITAL
AUDIO
(OPTICAL
OUT)
HD DVR
PC
PC
ENT
R
E
T
U
R
N
T
O
O
L
S
TV/VIDEO
TV
MUTING
DVD/
VCR
SAT/
CABLE
DVR
POWER
TV POWER
JUMP ANT MTS/SAP
FREEZE
SOUND PICTURE
TV/SAT
SUR
WIDE
W
E
G
A
VISUAL SEARCH
CH
VOL
REC
REC PAUSE
REC STOP
TOP MENU
MENU
F1
F2
G
U
ID
E
D
IS
P
L
A
Y
REPLAY
G
A
T
E
ADVANCE
PLAY
PAU S E
PREV
NEXT
STOP
TV