Filter
Top Products
TAV-L1 US 2-687-041-11 (1)
TAV-L1
2-687-041-11 (1)
Quick Setup Guide
Sony Corporation © 2006 Printed in Japan
If your product is not working properly
DO NOT RETURN TO THE STORE.
For service and technical assistance
Call our Customer Information Service Center (Toll Free):
1-800-222-SONY (7669) for US residents.
1-877-899-SONY (7669) for Canadian residents.
Please follow the steps to setup your system:
Manufacturer’s Codes
Cable Boxes
Manufacturer Code
Sony 101
Hamlin/Regal 123, 123, 125, 126, 127
Jerrold/G.I./Motorola 102, 103, 104, 105, 106, 107, 108, 109, 117,
118, 119, 123, 133
Oak 128, 129, 130
Panasonic 111, 113, 120, 121, 122, 131
Pioneer 113, 116
RCA 132
Scientific Atlanta 110, 111, 112
Tocom/Philips 117, 118
Zenith 113, 114
Satellite Receivers
Manufacturer Code
Sony 201
Hitachi 205
General Electric 202
Hughes 204
JVC/Dish Network/Echostar 210
Mitsubishi 209
Panasonic 203
Philips 211
RCA/PROSCAN 202, 208
Samsung 212
Toshiba 206, 207
1
Preparing for Use
Inserting Batteries into the Remote Control
Insert two size AA batteries (supplied) by matching the
and
on
the batteries to the diagram inside the remote control’s battery
compartment.
Attaching the frame grille
2
Connecting Your
System
1 Remove the covers.
2 See reverse side to connect this system and other equipment.
3 Connecting the FM wire antenna.
DVDVIDEO
DIGITAL
IN
OPT
COAX
DIGITAL
OUT
FM
ANTENNA
75
COAXIAL
FM wire antenna
4 Bundle the connected cords, then replace the covers.
Note
Depending on the connected equipment cords, the back covers may not attach properly. In
this case, try other cords, or use the system without the back covers.
1
2
3
4
Preparing for Use Connecting Your System
(See reverse side)
Running Initial
Setup
Programming
the Remote Control
4
Programming the
Remote Control
The remote control is preset to operate Sony brand video equipment.
Sony Equipment Programmable Code Number
Cable 101 (DVR)
Satellite receiver 201 (DSS)
Follow the steps below to program your system’s remote control to
operate the other video equipment.
Using the code list below, find the three-digit code number for the
manufacturer of your equipment. (If more than one code number is
listed, use the number listed first.)
1
1
3
2
Press and hold CABLE or SAT (FUNCTION) you
want to program and press POWER
simultaneously.
The selected FUNCTION button will flash.
Enter the three-digit manufacturer’s code number
using the number buttons while the button is lit,
approximately 30 seconds.
Press ENT.
When the programming is correct, the selected
FUNCTION button will flash twice slowly, and
when not, flashes five times quickly.
To check if the code works
Aim your system’s remote control at the equipment,
and press POWER. If the equipment responds, the
programming is completed. If not, try the next code
listed.
Tips
• If no code is input within the above specified time, or an invalid or
incorrect code number is input, the remote control automatically
goes back to the previous setting.
• In some cases, you may not be able to program your remote control
to operate other equipment. In such cases, use the equipment’s
own remote control.
• Dead batteries or removing the batteries may cause the
programmable codes to be lost and revert back to factory settings.
Reprogramming the codes may be necessary.
• Review the following chart to determine which diagram to use to
connect the equipments in your system:
For these equipments See reverse side
A
B
C
or
D
E
or
F
• See the “Cords Required” chart that appears with the diagram to
determine which cords you’ll need. You may need to purchase
extra accessories, such as cords, depending on the equipments you
plan to connect.
• Turn off and unplug all equipments before making connections.
Making Video Connections
Your system includes
several types of
video inputs. Use the
inputs that are
available on your
equipments that
provide the best
video performance,
as shown in the table
on the right.
Best Video
Performance
Connector type
HDMI*
(High-Definition
Multimedia Interface)
S VIDEO
Composite video
* Support 480i, 480p, 720p, 1080i
3
Running Initial Setup
3
6
7
1
2
4
5
Press POWER to turn on the system.
The Initial Setup screen appears.
Press MONITOR to switch the remote
FUNCTION to MONITOR.
Press
/
to select the monitor language displayed
on the menu screens, then press (OK).
Press DVD (FUNCTION) to switch the remote
FUNCTION to DVD.
Press DVD (direct input select) to switch the input
to DVD.
Press (ENTER) without inserting a disc.
The Setup Display for selecting the DVD language
used in the on-screen display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
To set, press , then .
PORTUGUESE
FRENCH
ENGLISH
ENGLISH
SPANISH
Press
/
to select the language, then press
(ENTER).
The system displays the on-screen display, the
menu and subtitles in the selected language.