Splendide WD2100XCP Washer/Dryer User Manual


 
Sold Separately
SecureFit Bracket Kit
#MK01 (for RV/Marine
installations)
Data Sheet Includes Information On
Splendide
Product Model Number
WD2100XC / WD2100XCP
Splendide 2100XC Laundry Center
Never reuse data sheets. Data sheets are subject to change without notice. Never use data sheets for final installation criteria.
Complete installation instructions are available upon request and in the owner's manual that comes with the unit.
Rear View (not to scale)
Side View (not to scale)
33
1
/2"
Minimum Installation
Clearances
23
7
/16"
Water Inlets
H
C
(Depending on
positioning of
leveling legs)
22
1
/2"
2
1
/4"
4
3
/4"
29
1
/2"
2
1
/2"
29
1
/2"
3"
33" to 33
3
/8"
4"
Vent Adapter
Drain Hose
Electrical
Connection
23
7
/
16
"
23
5
/
8
"
4"
Vent Adapter
21
1
/2" total case depth*
22
5
/8" total depth including
vent adapter and door handle
21
7
/8"
1"
37
5
/8"
Drain Hose
U-Clamp
5
/8"
Specifications:
· Weight: 148 lbs.
- Dimensions: 23.4”W x 33-33.4”H x 22.6”D (see right)
- Capacity: Wash - 2 to 15 lbs / Dry - 2 to 11 lbs.
Electrical Requirements:
· Volt/Amp/Hz: 120V, 11 Amp, 60 Hz.
· Maximum Absorbed Power: 1300 Watts
· Connection: 3-prong plug with 6' cord provided.
· Circuit/Protector: 3-wire single phase, 120V, 60Hz,
AC, on a separate 15-ampere circuit.
Water Connections:
· Maximum Pressure: 0.69 MPa (6.9 bar), 100 PSI
· Minimum Pressure: 0.05 MPa (0.5 bar), 7.5 PSI
Installation Location:
· Unit may be installed in recessed area, closet, or
alcove.
· Air Space Requirements: 0" on sides and 1" in front
and back (from the case). Additional installation
spacing needs to be considered for easy
installation, servicing, and compliance with state and
federal codes.
· Floor must support at least 280 lbs. and be a solid,
level surface.
· When locating in a towable trailer or watercraft,
position the machine over the axles or midship
where movement is at a minimum. Block unit in to
prevent extreme movement.
- Splendide #MK01 SecureFit Bracket kit available to
prevent shifting in RV and Marine installations.
Standpipe Drain System/ Sink Draining Req:
· Needs a 1 ¼" (3.2 cm) minimum diameter standpipe
with the minimum carry-away capacity of 7 gallons
(26 liters) per minute. Top of standpipe must be at
least 25" (62 cm) high and no higher than 34" (86
cm) from the bottom of the washer.
· Outlet end of drain hose (provided with the unit)
must be at least 20" above bottom of washer. An air
break must be available at the standpipe to avoid
siphoning.
· Faucet Adapter Kit #154187104A is available to
allow for direct faucet connection. See complete
installation instruction on drain hose draining directly
into sink, connection to dishwasher Wye fitting, and
disposer/drain connection in owners manual.
· Optional Drain-A-Way™ Pans are available. Pan
#PI-22 for cabinet or undercounter installations. Pan
#P-24 for freestanding installations. Both are
designed to be drain plumbed.
Exhaust Requirements:
· DO NOT exhaust dryer into a chimney, furnace, cold
air duct, attic, crawl space, or another duct used for
venting
· If cabinet door is installed, a minimum of 8 sq.
inches should be provided. Louvered doors with
equivalent air openings are acceptable. Allow
clearance behind the door(s) to avoid rubbing
between back of cabinet door(s) and front of unit
control panel. Additional clearances for wall, door
and floor moldings may be required.
· Rigid or flexible metallic duct required (NOT
INCLUDED). Ducting must slope downwards and
away from the machine.
2 Water Inlet
Hoses (8' length)
Included
Electrical
Connection
(6' cord length)
Flexible Drain
Hose (5' length)
Drain-A-Way
Pan #PI-22, P24
Custom Vent Kits
#VI-422, VI-D401