Toshiba 23L1400UC TV Antenna User Manual


 
Your TV comes with:
• Remote control and batteries
• Resource Guide.
• Pedestal stand and hardware
• All other cables and adapters are sold
separately.
• If any items are missing or damaged, notify
your dealer immediately.
• For Canada, the terms and conditions of
the Limited One (1) Year Warranty on Parts
and Labour can be found at
www.toshiba.ca/support Click on Televisions,
Select Warranty, then Select Standard Warranty
& Service Plans and Select Flat Panel
Television (bilingual)
The Resource Guide contains important safety precautions not included in this
document. Please review completely prior to using this product. Complete
instructions are contained in the User's Guide located on Toshiba's web site at :
www.toshiba.ca/support/ceg
Register Your Toshiba Television
Enhance your ownership experience by taking a few minutes to register your Toshiba product at
support.toshiba.ca/warranty/ (for L1400UC series). Completing product registration allows Toshiba to provide you
with product information updates, special offers and promotions. Failure to complete product registration will not diminish
your rights under the Standard Limited Warranty.
Pedestal Assembly Instructions
To prevent possible electric shock, protect the power cord
from being pinched when attaching the pedestal stand.
Before beginning pedestal assembly, carefully lay the front of
the LCD Panel face down on a flat, cushioned surface such as a
quilt or blanket. Leave the bottom of the unit protruding over the
edge of the surface and assemble pedestal as indicated below.
Two people are required for installation to avoid injury or
damage to the TV.
Extreme care should always be used when attaching the
pedestal stand to avoid damage to the LCD panel.
For safety information, please review the User’s Guide online:
For Canada: www.toshiba.ca/support/ceg
QUICK START
Check the components
Unpack the box
1. Remove the components and TV from
the box. Save the packing materials in
case you need them later.
2. Remove the documentation for
important information.
A High-Definition signal is needed to receive a High-Definition picture.
Once you have a High-Definition signal you need to connect it to a
High-Definition input on your TV. Not all channels are currently
broadcasting in HD. Standard analog TV channels and HD channels, even
on the same network, broadcast on different channels. (Example: ABC
analog may be on channel 4, while ABC-HD may be on channel 104.)
To display your TV using a Wall Bracket:
Be sure to remove the pedestal stand before mounting your TV with a
wall bracket. Always use a wall bracket Listed by an independent
laboratory (such as UL, CSA, ETL) that is appropriate for the size and
weight of the TV:
Two people are required for installation to avoid injury or
damage to the TV.
1. Unplug and remove any cables and/or other component connectors
from the rear of the TV.
2. Follow the instructions provided with your wall bracket. Before
proceeding, make sure the appropriate bracket(s) are attached to the
wall and the back of the TV as described in the instructions provided
with the wall bracket.
Always use the screws supplied or recommended by
the wall mount manufacturer.
VESA Mounting Pattern
TV Size Hole Pattern (H x V) Screw Size
23" 100mm x 100mm M4
L1400UC Series
To display your TV on the included Pedestal Stand:
Observe the following safety precautions:
1. Read and follow the pedestal assembly instructions section in this document
Before beginning pedestal assembly, carefully lay the TV facedown on a
flat, cushioned surface such as a quilt or blanket. Leave the bottom of the
unit protruding over the edge of the surface and assemble the pedestal as
indicated below.
Extreme care should always be used when attaching or removing the pedestal
stand to avoid damage to the display panel.
2. Assemble the pedestal stand with the hardware provided.
3. After assembling the pedestal, place the TV on a sturdy, level surface that can
support the weight of the TV.
4. Be sure to secure the TV to a wall stud, pillar, surface, or other immovable structure.
Choosing a location for your LED TV
23L1400UC (Canada model)
Many questions regarding parts, service, and warranties can be answered by visiting the Customer
Support Section of our website:
THANK YOU
If you are experiencing a technical problem or have questions regarding operation, authorized service centers,
warranty or parts, please contact our Customer Support Center at:
Always place the TV on a sturdy, level, stable surface that can support
the weight of the unit. Secure the TV with a mounting screw.
• Place the TV on a sturdy surface that has a sufficient
thickness and screw the unit to the surface securely by using a
mounting screw and the fall-prevention screw hole. (Mounting screw
not included)
For L1400UC series (Canada model):
1-800-268-3404 From within Canada
L1400UC series: www.toshiba.ca/support/ceg
Get detailed product information:
For up-to-date product information,
visit www.toshiba.ca/support/ceg
For detailed product specifications,
Select Product, then select Model
and select Model Number.
23L1400UC model
x 1
23 L1400UC
B
x 1
23 L1400UC
x 6 (23L1400UC)
C
23 L1400UC
M4 ; L12mm
23” TV
VESA Mounting Pattern
(Sample illustration)
Two stand screws
Subject to Change.
Product specifications, configurations, prices,
system/component/options availability are all
subject to change without notice.
Notice