7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
[OPERATE] button
[STOP] button
Playback mode indicator
[OPERATE] indicator
[PLAY] button
[TIME MODE+/
–] button
[HDR] indicator
Press the [OPERATE] button to turn the operating mode
on.
The [OPERATE] indicator lights.
Press the [TIME MODE +/
–] button to set the play mode
to 2H (SP) or 6H (EP) mode.
The [2H] or [6H] indication is shown on the display.
• To play back a tape recorded in the timelapse mode
at slow speed, press the [TIME MODE +/
–] button
to set the desired mode (L12H, L18H, L24H, 24H
..... 960H) (slow play).
• Avoid using slow-motion playback continuously for
long periods (more than several hours).
Load the recorded cassette correctly.
* If a cassette is loaded when the operating mode is off,
the operating mode is switched on automatically (auto
operate on function).
If the cassette’s safety tab has been removed, the
operating mode is turned on and play starts
automatically (auto play function).
Press the [PLAY] button to start play.
The play indicator is shown on the display and
the Play mode is engaged.
When a tape recorded in the HDR mode is played back,
the [HDR] indicator lights.
* No sound is output in the Timelapse Play mode
(except for L12H, L18H and L24H modes).
When the play mode is set to 2H (SP) or 6H (EP),
playback operates as follows.
• Cassettes recorded in the 2H or ordinary (SP)
Timelapse modes are played back in the 2H (SP)
mode. [2H] is shown on the display.
• Cassettes recorded in the 6H or HDR Timelapse
mode are played back in the 6H (EP) mode. [6H] is
shown on the display
To stop playback
Press the [STOP] button.
The tape stops and the Stop mode is engaged.
7-1 Preparation 7-2 Playback
* To listen to the sound recorded in the L12H, L18H
and L24H modes, play the tape back in the same
mode used for recording (L12H, L18H or L24H).
* When a tape recorded in the 2H mode is played
back in the L12H or L24H mode, noise appears in
the picture.
When a tape recorded in the 6H mode is played
back in the L18H mode, noise appears in the
picture.
Press the [TIME MODE +/
–] button to set the
playback speed to 2H or 6H and start playback.
* Noise may appear in the picture with tapes not
recorded on the SR-9080U.
Connection
Connect the output connectors on the rear panel correctly.
Menu switch setting
Set the menu switches in <VIDEO/VTR MODE> as
required.
5
[V. PULSE] ... Factory setting: OFF
Set to “ON” to add V. pulse in the normal play (2H or
6H) mode.
5
[CNT MEM SW] ... Factory setting: ON
Counter memory ON/OFF.
• Set to “ON” to use the counter memory function.
5
[AUTO REW] ... Factory setting: OFF
Automatic rewind ON/OFF.
• Set to “ON” to rewind the tape to the beginning when
the tape ends.
5
[REPEAT PLAY] ... Factory setting: OFF
Repeat playback ON/OFF.
• Set to “ON” to execute repeat playback.
U model
46 (U)
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
[OPERATE] button
[STOP] button
Playback mode indicator
[OPERATE] indicator
[PLAY] button
[TIME MODE+/
–] button
Press the [OPERATE] button to turn the operating mode
on.
The [OPERATE] indicator lights.
Press the [TIME MODE +/
–] button to set the play mode
to 3H (SP) mode.
The [3H] indication is shown on the display.
• To play back a tape recorded in the timelapse mode
at slow speed, press the [TIME MODE +/
–] button
to set the desired mode (L12H, L24H ..... 960H)
(slow play).
• Avoid using slow-motion playback continuously for
long periods (more than several hours).
Load the recorded cassette correctly.
* If a cassette is loaded when the operating mode is off,
the operating mode is switched on automatically (auto
operate on function).
If the cassette’s safety tab has been removed, the
operating mode is turned on and play starts
automatically (auto play function).
Press the [PLAY] button to start play.
The play indicator is shown on the display and
the Play mode is engaged.
* No sound is output in the Timelapse Play mode
(except for L12H and L24H modes).
To stop playback
Press the [STOP] button.
The tape stops and the Stop mode is engaged.
7-1 Preparation 7-2 Playback
* To listen to the sound recorded in the L12H and
L24H modes, play the tape back in the same mode
used for recording (L12H or L24H).
* When a tape recorded in the 3H mode is played
back in the L12H or L24H mode, noise appears in
the picture.
Press the [TIME MODE +/
–] button to set the
playback speed to 3H and start playback.
* Noise may appear in the picture with tapes not
recorded on the SR-9080E/EK.
* Tapes recorded in the LP mode cannot be played
back. In this case, the [LP] indication blinks on the
display.
Connection
Connect the output connectors on the rear panel correctly.
Menu switch setting
Set the menu switches in <VIDEO/VTR MODE> as
required.
5
[V. PULSE] ... Factory setting: OFF
Set to “ON” to add V. pulse in the 3H (SP) play mode.
5
[CNT MEM SW] ... Factory setting: OFF
Counter memory ON/OFF.
• Set to “ON” to use the counter memory function.
5
[AUTO REW] ... Factory setting: OFF
Automatic rewind ON/OFF.
• Set to “ON” to rewind the tape to the beginning when
the tape ends.
5
[REPEAT PLAY] ... Factory setting: OFF
Repeat playback ON/OFF.
• Set to “ON” to execute repeat playback.
E model
