Daewoo DV6T544B DVD Player User Manual


 
46 47
The others
Before doubting about troubles (VCR)
¥ Recording a TV program is impossible.
¥ Once pressing [REC], a videotape is
ejected automatically.
¥ Timer recording of Cable TV does not
work.
¥ In spite of pressing [CHANNEL], a
channel can not be set.
¥ While duplicating, screen is not clean
and distorted.
¥ remote control does not work.
¥ Buttons on remote control do not
work.
¥ VISS index search does not work.
¥ Cable broadcasting can not be
selected.
Checks
Symptom
Please check whether a channel is fixed on video. If not, you have to
turn it into ÒTVÓ by pressing [OUTPUT] button.
Please check whether the timer recording info is right.
Are RF cables inputted antenna connection terminal correctly?
Does a CH number selected in display section appear?
Please check a tab on a tape whether it is broken or not. (If it was
broken, please scotch-tape it)
Check whether the screen is displayed in VCR Only Channel. Press
[OUTPUT] button in this remote controller to adjust in "General
Broadcast" condition.
Is the rounded line (RF cable) connected in "ANT.IN" terminal?
Please check whether the clock is right.
Does the display on your video show Ò
Ó
(Ready to timer recording)?
Please make it out.
Please check whether the timer recording info is right.
Please check a tab on a tape whether it is broke or not. (If it was
broken, please scotch-tape it)
Was a cable data output code connected correctly?
Were a converter manufacturer setup and output channel right?
Did you enter a password? (Please cancel it.)
Did you turn off your player? (Please turn it on.)
You may not memorize channels.
Please check your channel setting or press a number button.
Some tapes or discs distributed in the market for lending is set to
prevent copy in manufacturing. These tapes cannot be duplicated in
a good condition.
Battery may be weak or exhausted.
A receiver of remote control may be different with a sender.
In case a videotape is positioned in the beginning, ÒVISS REWÓ and
ÒREWÓ do not work.
In case a videotape is positioned in the end, ÒFFÓ, ÒVISS FFÓ, ÒPLAYÓ
and ÒRECÓ do not work.
Please check whether another button is pressed.
Are you playing a tape that is not recorded in this recorder? (Try to
record it with the recorder.)
You may start recording it in ÒREC-PAUSEÓ. Please start recording it
from stop condition.
Please select ÒCABLEÓ not ÒNETWORKÓ from the ÒCHANNEL SETTINGÓ.
Before doubting about troubles (VCR)
¥ ÒPower OnÓ does not work.
¥ It does not work even in ÒPower OnÓ.
¥ A videotape is not inputted in.
¥ On inputting a videotape, the tape is
re-ejected.
¥ A videotape is not ejected.
¥ A channel on video and a play screen
does not appear.
¥ Noise (screen noise) appears on
screen.
¥ Noise appears on screen after
recording.
¥ While in playing, noise appears.
¥ Sound and screen are irregular.
¥ Sound comes out but screen does not
appear.
¥ Screen is irregular and stripes appears.
¥ "Screen Error" message is displayed in
a screen.
¥ While recording and playing, the top
of screen extremely waves.
¥ A screen is not clear.
¥ A screen at pause is trembling or slow
screen is not clear.
Checks
Symptom
Please check whether a power plug is inserted in an electric outlet.
Please check whether a videotape is inserted in.
Try to insert a plug again.
Please check whether a power plug is inserted in an electric outlet.
Please check whether a videotape is in.
Please check whether a videotape is inserted in a right direction (a
side of transparent window should be on the upside)
Have you inputted a videotape again just after the tape was ejected?
Please try it again after fully ejecting it.
When a videotape forces to be ejected, the tape may not be inputted.
In the case, please pull out an outlet, and then push the tape
smoothly.
ThatÕs why a safe mode to protect a videotape is operated
automatically. Please pull out the tape and input it again.
In case the product is used for a long time, a videotape may not be ejected
for a film inside may be stretched. In the case, please pull out a power plug
for about 10mins and then press [EJECT] button.
Please check your antennaÕs connection.
TV channel should be fixed on video channel (3 or 4).
Please check your antennaÕs signal whether it may be weak. In case of
its weakness, please use a frequency amplifier connected with the
device.
Press [TV/VCR] and then let ÒVCRÓ is displayed on the display panel.
While in no use of VCR, was it turned on?
While in recording a program, do you watch another channel?
Select TV by pressing [TV/VCR] button on remote control.
While in playing a videotape, there may happen some noise or blot in
the part of the beginning of a videotape or resuming ÒPAUSEÓ, which
are not breakdown.
Please press [TRACKING] for better screen. Videotape may be poor.
Try to change it to another one.
Please use a head-cleaner to clean VCR heads. VCR heads may be
contaminated.
Since VCR Play signals are not stable like a TV signals, screen may be
unstable or curved while in playing. To fix the problem, please
horizontal adjustment.
In case videotape is the one recorded by other products or old one,
stripe may appear on the screen.
Try to adjust the screen by [TRACKING+/Ð] button.
Try to use a head-cleaner.
Try to use a head-cleaner.
Try to adjust the screen by [TRACKING+/Ð] button.