Filter
Top Products
DDEENNOONN EELLEECCTTRROONNIICCSS ((UUSSAA)),, IINNCC..,, 1199 CCHHAAPPIINN RROOAADD,, BBUUIILLDDIINNGG CC,, PPIINNEE BBRROOOOKK,, NNJJ 0077005588
MMAAIINN:: ((997733)) 339966--00881100
WWEEBB SSIITTEE AADDDDRREESSSS:: hhttttpp::////wwwwww..uussaa..ddeennoonn..ccoomm
2
• For these adjustments we highly recommend you use an SPL (Sound Pressure Level) meter,
Radio Shack makes a excellent analog one for about $35. This exercise is similar to setting
up the surround processor, with a twist. Since you are using test tones generated inside the
players, and not the processor, it is crucial that you first have your Receiver/Pre-pro
calibrated. This is because the better processors automatically raise their volume controls
when doing test tone calibration, and once you have completed the processor’s calibration
you now have a test tone reference point for the DVD player.
• Using the display, or indicator on the volume control, mark down the reference point volume of
your processor when it is outputting its internal test tones, and set the volume to that point
before calibrating the player.
• We suggest setting the ‘Test Tone’ to manual as this setting allows you to control the tempo of
calibration, not the player. It is also easier on the nerves. Go through each channel, so they
calibrate to, or as close to, 75dB on the meter. The test tone outputs on the player may not be
enough to get to true 75dB (depending on the External Inputs output settings – see below), so
get close, but make sure all the channels measure to the same point.
• Many receivers/pre-pros have individual channel input and/or output level controls on
their External Inputs, these may need to be adjusted to obtain proper calibration.
Please check out the product’s Owners Manual for assistance. All DENON AVRs have
independent output level controls for the External Analog Inputs, while the 28/38/5803
models also have a Subwoofer Input Level control adjustment.
• If your particular product does not have level controls, DENON recommends to set the
5 Main Channel levels to their lowest output setting and leave the Subwoofer at 0dB
(highest output setting) in the player before starting the calibration process.
• YOU MUST THEN SETUP THE ‘PURE DIRECT MODES’ ON THE 9000/3800. THIS IS DONE BY
DEPRESSING THE BUTTON ON THE REMOTE LABELED ‘PURE DIRECT MEMORY’; YOU
WILL SEE THE ON-SCREEN DISPLAY FOR THIS FUNCTION. IN ‘PDM’ YOU CAN
DETERMINE WHICH CIRCUITRY TO LEAVE ‘ON’ OR TURN ‘OFF’, LIKE DIGITAL OUTPUT,
VIDEO OUTPUT AND THE FRONT DISPLAY.
• With Mode 1, we recommend to leave ‘On’ the digital and video circuits, the display is your
choice. The ‘Pure Direct Mode 1’ would be selected for DVD-Video/CD/CD-R/RW/MP-3
playback, by the knob on the front panel of the 9000/3800. If you decide not to make any
adjustments here, you can take the following tips for ‘Mode 2’ and set them for ‘Mode 1’.
Then for playback of the above listed disc types, you would leave the ‘Pure Direct Mode’
switch in the ‘Off’ position.
• With ‘PD Mode 2’ (or ‘1’), the only setting you must change is the ‘Digital’ option. Change from
‘On’ to ‘Off’, the others are user preference. ‘Pure Direct Mode 2 (or ‘1’)’ would be selected for
DVD-Audio and/or DVD-Video 24/96 Music playback (Chesky or Classic DADs). Users would
adjust the ‘Pure Direct Mode’ knob upon changing of the different disc format type.
• If you do not setup the ‘Pure Direct Modes’ and leave the selector in the ‘Off’ position,
DVD-V/CD/CD-R/RW/MP-3 discs will play fine, however DVD-Audio discs (copy
protected or not) may not play the Hi-Resolution Multi-Channel format.