Dynex DX-24L230A12 Flat Panel Television User Manual


 
Online User Manual
3
DX-24L230A12 and DX-32L220A12
If your TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions because incorrect adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore your TV to its normal
operation.
If your TV has been dropped or damaged in any way.
When your TV exhibits a distinct change in performance.
Outdoor antenna grounding
If an outside antenna or cable system is connected to your TV, make sure
that the antenna or cable system is grounded to provide some
protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA No. 70, provides
information with respect to correct grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of the
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Note to CATV system installer
Article 820 of the National Electrical Code, ANSI/NFPA No. 40 provides
guidance for correct grounding. Specifically, it states that the cable
ground must be connected to the grounding system of the building as
close to the point of cable entry as practical.
Condensation
Moisture will form on the TV if the TV is brought from cool surroundings
into a warm room or if the temperature of the room rises suddenly.
When this happens, the TV's performance may be impaired. To prevent
this, let the TV stand in its new surroundings for about an hour before
switching it on, or make sure that the room temperature rises gradually.
Condensation may also form during the summer if the TV is exposed to
the breeze from an air conditioner. In such cases, change the location of
the TV.
Mobile telephone warning
To avoid interference with your TV picture and sound, operating
problems, or even damage, keep your cordless and cellular telephones
away from the TV.
End of life directives
Your TV contains tin-lead solder. Disposal of this material may be
regulated for environmental reasons. Your TV also contains material
that can be recycled and reused. For disposal or recycling information,
contact your local authorities or the Electronic Industries Alliance at
www.eia.org to find a recycler in your area.
Non-active pixels
The LCD panel contains almost 3 million thin film transistors, which
provide exceptionally sharp video quality. Occasionally, a few
non-active pixels may appear on the screen as a fixed blue, green, or red
point. These non-active pixels do not adversely affect the performance
of your TV, and are not considered defects.
Online User Manual
WE ARE GOING GREEN! For the full user manual, go to
www.dynexproducts.com and click Support & Service. Enter your
model number in the Product Search field, then click Search.
Troubleshooting
Video and audio
Antenna lead-in wire
Grounding clamp
Antenna discharge unit
Grounding conductors
Ground clamps
Power service grounding electrode system
Electric service equipment
2
1
3
4
5
6
7
1
2
3
4
5
6
7
Warning
Do not try to repair your TV yourself. Contact
authorized service personnel.
Problem Solution
Picture does not fill the
screen. There are black bars
around the picture.
Change the aspect ratio. An increasing amount
of digital TV and movies are presented in wide
screen (16:9). See “Adjusting the TV picture” in
the online User Guide.
No picture (screen is not lit)
and no sound.
Press on the TV or the remote control.
•Make sure that Audio Only option is set to Off.
See “Playing TV audio only” in the online User
Guide.
Make sure that the video cables are connected
securely to the back of your TV.
Adjust the contrast and brightness. See
“Adjusting the TV picture” in the online User
Guide.
Make sure that the power cord is plugged in.
Make sure that the correct video input source is
selected. See “Selecting the video input source”
in the online User Guide.
Try another channel. The station may be
experiencing problems.
Make sure that the incoming signal is
compatible.
Make sure the antenna or cable TV is connected
correctly and securely. See “Connecting a cable
or satellite box” or “Connecting an antenna or
cable TV (no box)” in the online User Guide.
Check the closed caption settings. Some TEXT
modes can block the screen.
DX-24L230A12-32L220A12_11-0075_IMP INFO.book Page 3 Tuesday, January 25, 2011 9:53 AM