Emerson CETD204 TV VCR Combo User Manual


 
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
Connect your TV/VCR/DVD and a Source (Playing)
VCR using the following diagram.
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the TV/VCR/DVD’s cassette
compartment.
3)Press the SPEED button on remote control for the
TV/VCR/DVD to select the desired recording
speed (SP/SLP).
4)Press the CHANNEL button
K or L on the
TV/VCR/DVD until “AUX” appears on the screen.
5)Press the RECORD button on the TV/VCR/DVD.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/VCR/DVD’s front panel controls whenever pos-
sible. The remote control might affect the source
(Playing) VCR’s playback operation.
7)To stop copying, press the STOP/EJECT button on
the TV/VCR/DVD, then stop the tape on the
source VCR or camcorder.
TV/VCR
VIDEO
IN
OUT
AUDIO
IN
OUT
L
R
- 31 - EN
1C29
OTR (One Touch Recording)
Push(es) Display Recording length
1 push (normal recording)
2 pushes 0:30 30 minutes
3 pushes 1:00 60 minutes
17 pushes 8:00 480 minutes
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
[Fig.8]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
[The TV/VCR/DVD]
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/VCR/DVD.
Make sure ...
TV/VCR/DVD power must be turned on.
Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape
to the point at which you want to begin recording.)
NOTES:
You cannot start OTR with the remote control.
Recording starts immediately when the REC/OTR
button is pressed.
When the REC/OTR button is pressed 18 times, the
TV/VCR/DVD returns to the Normal Recording mode.
To stop the OTR operation, press the STOP button
on the TV/VCR/DVD or on the remote control.
To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up
momentarily then disappear.)
Recording stops when 0:00 is reached.
Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-120).
If the tape runs out before the end time, the
TV/VCR/DVD will switch to the Stop mode
immediately, ejects the tape and turns itself off.
If you press the POWER button during OTR, the
TV/VCR/DVD continues recording until the
selected length is reached.
1 Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL button K or L.
Remember: If the TV/VCR/DVD is connected to a
cable box or satellite box, the TV/VCR/DVD must
be on CH3 or CH4, then the channel to be recorded
is selected on the cable box or satellite box.
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3 Begin OTR
Press the REC/OTR button on the
TV/VCR/DVD as many times as
needed. The recording length will be
determined by the number of times
you press the REC/OTR button. Each
additional push will increase the
recording time by 30 minutes. It is set up to 8 hours.
TV/VCR
OTR(2 : 30)
SP