Emerson EWC1902 TV VCR Combo User Manual


 
- 11 - EN
9I03
CLOCK SET UP
(AUTO / MANUAL)
Make sure ...
TV/VCR power must be turned on.
Confirm that the antenna connections are correct.
The cable converter box must be turned on if your
TV/VCR is connected directly to it. (See NOTES:)
The channel is properly set in advance.
NOTES:
Auto clock setting only needs to be set once. But it
can be done again if the clock’s time has become
incorrect for some reason.
If the TV/VCR is connected directly to a cable
converter box or satellite box, the local PBS station
must be selected on the cable box itself, and the
TV/VCR must be set to the output channel of the
cable converter box or satellite box (usually chan-
nel 3 or 4), to be able to set up or correct the clock
automatically.
If you do not know what your local PBS station is,
then follow “MANUAL CLOCK SETTINGS”.
The TV/VCR cannot control the channels of the
cable converter box or satellite box.
1 Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
2 Set “AUTO CLOCK” to [ON]
Press the F.FWD/B or REW/s
button repeatedly until [ON]
appears.
3 Enter the channel number for the PBS station
Press the PLAY/K or STOP/L button to point to
“AUTO CLOCK CH”.
Then press the F.FWD/B or
REW/s button until the channel
number for your local PBS station
appears.
If you do not know the PBS channel
number, leave it set to [AUTO] which is located
before [2]. The TV/VCR will search automatically all
available channels for the local PBS station, and will
select that channel.
4 Exit the Auto Clock Setting
Press the MENU button on the remote control to
return to TV mode.
5 Turn off the TV/VCR
Turn the TV/VCR off. Because the Auto Clock func-
tions automatically while the TV/VCR is off.
– SETTING CLOCK –
B AUTO CLOCK [ON]
AUTO CLOCK CH [AUTO]
MANUAL CLOCK SET
D.S.T. [OFF]
– SETTING CLOCK –
AUTO CLOCK [ON]
B AUTO CLOCK CH [AUTO]
MANUAL CLOCK SET
D.S.T. [OFF]
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Set the clock accurately for proper automatic timer
recording. If the Public Broadcasting Station (PBS)
is available in your area, follow “AUTO CLOCK
SETTING”. If it is not, follow “MANUAL CLOCK
SETTING”.
AUTO CLOCK SETTING
You can have the TV/VCR set the clock automatical-
ly by using the Public Broadcasting Station (PBS)
channel in your area. Once you have set the clock by
using the following procedure, the TV/VCR will
automatically monitor the correct time and date
being broadcast by the PBS station in your area,
using a new service called Extended Data Service
(XDS).
If you choose [AUTO],
The TV/VCR must search until the PBS channel is
found. It must scan each channel for a couple of
seconds to determine if that channel is transmitting
the XDS signal.
If the time, that is automatically set by this select-
ed PBS station is incorrect, it may not be your
local PBS station, but one from a different time
zone. Or there is a case that no channel is broad-
casting the XDS signal in your area, as shown by
no time. In these cases, you must manually enter
the correct local PBS station, or set the clock man-
ually and turn off the Auto Clock Setting feature.
MANUAL CLOCK SETTING
Make sure ...
TV/VCR power must be turned on.
In the example below, the clock is to be set to:
DATE May 7th, 2002
SETTING TIME 5:40PM
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the
CHANNEL K or L button on or directly pressing
the number buttons on the remote control.
Note for using the number buttons:
When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
You must proceed single-digit channel numbers
with a zero (Example: 02 ... 09).