Filter
Top Products
–
27
–
EN
Quick Use Guide
✄
Please refer to “Basic TV
Connection” on the front page
before you use this unit.
RF Output Channel
If channel 3 is already occupied for
broadcasting,
1)Set your TV to channel 4.
2)Insert a pre-recorded tape into this
unit.
3)Press the OUTPUT button on the
DVD/VCR so that the VCR OUTPUT
light is lit.
• If noise appears on the TV screen
,
press the VCR/TV button on the
remote control.
4)Press the PLAY button once.
5)After a few seconds, press the PLAY
button on the DVD/VCR for 3 sec-
onds.
• The RF output channel will change
to channel 4 from channel 3 and you
will see a playback picture.
• When a picture does not appear on
the TV screen, repeat step [4].
6)Press the STOP button to stop play-
back.
Connections
1
Clock Set Up
5
VCR/DVD Switching
3
Installing the Batteries
for the Remote Control
2
Turn on the unit for the
first time
4
2
3
1
OPEN/CLOSE
STOP/EJECTPLAY REC /OTR
TIMER REC
F.FWDREWPOWER
CHANNEL
OUTPUT
PLAYFWD/SKIPSTOPSKIP/REV
DVDVCR DISC IN
VIDEO AUDIO
OUTPUT
SKI
DVDVCR
POWER
DISPLAY VCR DVD PAUSE
SLOW
VCR/TV
SKIP/CH.
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
MODE
SUBTITLE
T-S E T
ANGLE
ENTER
RETURN
SEARCH
MODE
REPEAT A-B
OPEN/CLOSE
/EJECT
SPEED AUDIO
CLEAR/
C. RESET
123
456
789
0
+10
V.SURR
OUTPUT button
DVD OUTPUT
light
VCR OUTPUT
light
DVD button
VCR button
Press the VCR button on the remote
control.
(Verify that the VCR OUTPUT light is lit.)
VCR MODE
Note
• Pressing only the OUTPUT button on
the front panel DOES NOT switch the
mode of the remote control. You
MUST select the correct mode on the
remote control.
Press the DVD button on the remote
control.
(Verify that the DVD OUTPUT light is lit.)
DVD MODE
2
2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
POWER
3
3
CH 01
AUTO SET UP
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
Y
Y
es
es Press the MENU
button to exit
Do you connect the cable from the cable box or
the satellite box to the DVD/VCR’s ANT IN jack?
TV ScreenRemote Control
VCR
VCR
or
VCR
1
1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
MENU
CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
Select the current day
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
VCR
VCR
or
or
or
VCR
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
BPM
Select the current year
Select “AM” or “PM”
8
8 To exit the CLOCK SET
screen.
Select the current hour
Select the current minute
or
or
or
or
2
2
3
3
4
4
5
5
6
6
7
7
YES
NO