Filter
Top Products
RGB 460
xixi
xixi
xi Series • Installation and Operation
RGB 460
xixi
xixi
xi Series • Installation and Operation
Installation and Operation, cont’d
2-52-4
1
Faceplate screws — These screws secure the faceplate to the rest
of the interface.
Do not remove these faceplate screws while the interface
is attached to the wall or the detached interface may fall
down inside the wall.
2
Power/signal LED — This LED lights
• yellow to indicate that the interface is receiving power.
• green to indicate that an active sync signal is present at the
input and the interface is receiving power.
If the input signal has sync on green, the LED will not
change from yellow to green
3
No Monitor/Monitor switch (video input termination) — Set
this switch to select the video input impedance that provides the
best picture:
• No Monitor (75 ohms) if no local monitor is connected or if
the picture is too bright or blooming (unterminated).
• Monitor (high impedance) if a local monitor is connected, a
laptop breakout cable is used, or if the picture is too dark.
4
Audio input connector — Plug a 3.5 mm stereo plug into this
jack for unbalanced audio input. Wire the male plug as shown
below.
Tip (L) Sleeve (GND)
Tip (L)
Ring (R)
Sleeve (GND)
Audio input wiring
5
Computer input connector — Attach a cable from the computer
to the interface via this female 15-pin HD connector.
6
Buffered local monitor output connector — Attach a cable from
a local monitor to this female 15-pin HD connector.
7
Horizontal shift control knob (H. Shift) — While viewing the
displayed image, rotate this control to move the image to the
right or left on the screen. The Min/Max LED (
8
) will flash
red whenever the minimum or maximum limit of this control is
reached.
DDSP disables the horizontal shifting control.
8
Min/Max LED — This LED blinks red momentarily whenever
the minimum or maximum limits of the horizontal shift control
(
7
) have been reached. Continually turning the horizontal
shift control knob in the same direction after the limit has been
reached will cause the LED to continually blink.
9
Composite video connector (RGB 464
xixi
xixi
xi) — This female RCA-
to-BNC type connector provides pass-through capability for
composite video input.
10
S-video pass-through connector (RGB 464
xixi
xixi
xi) — Connect an S-
video source to this 4-pin mini DIN pass-through connector.
11
12
RCA audio connectors (RGB 464
xixi
xixi
xi) — Connect the left audio
signal cable to the white RCA connector (L/
Mono), and the right audio signal cable to
the red RCA connector (R) for unbalanced
stereo audio pass-through input. Wire the
RCA plugs as shown at left.
When a mono audio signal is applied to the L/Mono
input, the same signal will be output to both left and
right audio outputs.
13
Network connector (RGB 464
xixi
xixi
xi) — Connect a computer to this
RJ-45 female connector for pass-through to a network.
14
Opening for architectural adapter plates — The RGB 468xi can
accept up to four optional standard architectural adapter plates
(AAPs) attached here. The RGB 468 Mxi (not pictured) can
accept up to four optional mini architectural adapter plates
(MAAPs) attached here. The adapter plates come in a variety of
audio/video connectors.
Tip (Signal) Sleeve (Gnd)
#4-40 Nut w/ Captive
Washer
4-gang Wall Box
H
. S
H
IF
T
M
I
N/
M
A
X
T
M
RGB 468
IN
P
U
T
M
O
N
IT
O
R
AUDIO
R
G
B
4
6
8
W
IT
H
A
D
S
P
M
O
N
I
TO
R
N
O
M
O
N
IT
O
R