–
13
–
EN
VCR Functions
Hint
Hint
• To go back one step, hit [
ss
] (during
steps 3) to 9) ).
8
8
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
5
5 Select the desired start time
(hour).
Select the minute.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 – –
END TIME – – :– –– –
CHANNEL – –
REC SPEED – –
6
6
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME – – :– –– –
CHANNEL – –
REC SPEED – –
AM
BPM
Select “AM” or “PM”.
Select the desired channel.
• If you have connected the unit to a
cable box or satellite box as the
Connection on page 6, select the VCR
to channel 3 or 4 (the RF output chan-
nel of the VCR). Then, select the
desired channel at the cable box or
satellite box.Leave the cable box or
satellite box on for Timer Recording.
9
9
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP
B SP
SLP
Select the desired recording speed.
CLEAR/
C. RESET
1) Hit [SUBTITLE/T-SET] then, [VCR]
on the remote control.
2)
Select main menu by hitting [MENU].
3) Select “TIMER PROGRAMMING”
by pressing [K/L].Then, hit [B].
4) Select the program number which
you want to check by pressing
[K/L]. The details of the program
you selected will appear on the TV
screen.
• Go to the digit you want to
change by pressing [s/B].Then,
enter correct numbers by press-
ing [K/L].
• You may cancel the entire pro-
gram by hitting [s] while the pro-
gram number flashes.
5) Hit [CLEAR/C.RESET] to exit.
6) Hit [SUBTITLE/T-SET] to return to
timer stand-by mode.
Hit [STOP/EJECT
CC AA
]
on the unit.
To cancel a Timer Recording
in progress
To Check, Correct or Cancel a
Timer Program
• To set another program after step 9), hit [
BB
].
Then, continue with step 2).
or
or
or
or
or
• Hit [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode,
then hit [SUBTITLE/T-SET].
• If a tape is not in the unit or does not have the record tab, the TIMER light flashes and Timer Recording cannot be
performed. Please insert a recordable tape.
• When Timer Recordings are set, the TIMER light will appear. To use the VCR as usual until the time for the recording, hit
[SUBTITLE/T-SET] so that the TIMER light disappears. Hit [VCR/TV] to choose the VCR position. Select either VCR or
DVD mode, then continue with the other features as described in this manual.
After an OTR or a Timer Recording has been set, this unit operates as follows:
• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape and switches to the DVD mode
automatically. If the DVD power is off, the unit does not switch to the DVD mode but goes into the timer standby mode.
Press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then hit [VCR] to activate the VCR
function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is hit. ([SOURCE]
on the front panel and [VCR] on the remote control will not function.)
• To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then
hit [VCR] to activate the VCR function again.
• The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after
you cancelled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you
operate.
When an OTR or a Timer Recording is completed...
• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically,
and the TIMER light appears to indicate the unit is in the timer standby mode.
• The TIMER light flashes if there are no more Timer Recordings on standby.
• If Auto Power Off for DVD has NO
T been activated, the unit switches to the DVD mode and all the VCR function will be
unavailable.The TIMER light will not appear as long as the DVD is in use. All the DVD functions are available during OTR,
timer standby mode and Timer Recording.
If you want to use the DVD player during a Timer Recording or while the TIMER light appears or flashes.
• Hit [STANDBY-ON] to turn on the unit. Hit [DVD] on the remote control to choose DVD mode, then continue with the other
DVD features as described in this manual.You don’t need to set the TIMER off to use the DVD player.
NOTE (for Timer Recording) :
• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.
Hints for OTR and Timer Recording
10
10
•
The TIMER light on the
front panel appears.
The unit will change to
the DVD mode.
SUBTITLE
T-SET
7
7
Repeat the procedure in steps
5) and 6) to set the end time.
H9870UD_EN/SP.qx3 05.2.9 8:31 PM Page 13