Filter
Top Products
Setting Up Your Remote Control
Operation
SE LECT
CH.LIST
FAV.LIST
AUDIO LIST
PIP SWAP
AUDIO SWAP
POSITION
CC
P.MODE
S.MODE
FREEZE
EN
U
T
IM
E
N
PU
T
INF
O
E
X
IT
R
A
C
S
A
P
S
L
E
E
P
VOL+
CH+
Q.VIEW
OK
VO
L
-
CH-
Automatic Scan Programming the Controller
To automatic scan program the Controller:
1. Manually turn OFF the device you wish to power scan. (TV, VCR, DVD, STB, cable box or audio
equipment).
2. Press SELECT key to choose the device you wish to program.
While Press and holding OK key, press the SELECT key and device LED will be ON. Keep the status
for about 5 seconds, release both keys and then LED will blink twice per second, indicating that the
Controller is ready for programming.
3. Press and release the Mute key to enter automatic scan mode. And the remote will automatically
sending power codes to the device.
4. When the device turns ON, press OK key to program the Controller with the new code, saving it
and exit. To exit without programming, press any key other except OK key.
5. If the device responds, no further programming is required. If the device does not respond, repeat
steps 1 through 4. And search will start from current code set.
6. After searching the entire data base, this mode will be automatically exited and led will blink for 3
times.
Punch-Through Features
The Controller provides two punch-through features that allow users to control TV volume and DVD
or VCR operation while the Controller is in another device mode control certain features of another
device.
Volume Punch-Through:
The TV Volume/Mute punch-through feature allows you to control the volume and mute function of
your TV while the Controller is in another device mode. The feature is applicable for all devices and
brands that do not use the volume control buttons for other purposes.
Transport Key Punch-Through:
The DVD or VCR transport key punch through feature lets you control the PLAY, STOP, PAUSE,
REWIND, FF and RECORD functions of your DVD or VCR while the Controller operates in other
modes. The feature is applicable for all devices and brands that do not use the transport keys for
other purposes.
Protection mode:
1. While press and holding OK, press FREEZE key for 5 seconds to enter protection mode. In this mode,
all the above programming methods will be invalid.
2.To exit protection: While press and holding OK, press FREEZE key. Current device related LED remains
ON and then release OK and FREEZE. Input three digit password “8 8 8”, LED turns off and protection
mode is ended. If error password is input or no password input in 10 seconds, LED blinks three times
and then turns off. Protection mode will remain.
Display mode:
1.To enter display mode, while press and holding OK key, press the SELECT key and device LED will
be ON, keep the status for about 5 seconds. Release both keys and then LED will blink 2 times per
second, indicating controller is ready for programming.
2.Sequence press 9, 8, 0 to enter display mode. And LED is off now.
3.Press digit 1 key to get the first digit of current code set. For example, if the first digit of code set is 1,
so then led will blink once and remains OFF. Digit 0 in code set will not be displayed. Blink twice
per second.
4.Press digit 2 key to get the second digit of current code set. For example, if the second digit of
code set is 3, so then led will blink three times and remains OFF. Blink twice per second.
5.Press digit 3 key to get the third digit of current code set. Blink twice per second.
6.Only digit 1, 2, 3 are valid in this mode. And the sequence is not fixed. You can repeat, if you don't
remember clearly.
7.Controller will not send out data in this mode if user presses any keys other than digit 1, 2, 3. And
this can be regarded as no key pressed.
8.If no key was pressed in 10 seconds or any key other than digit 1, 2, 3 is pressed display mode
is ended.
Owner s Manual 37