Filter
Top Products
Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:1,
V:2, V:3, V:4, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT
A, V:1, V:2, V:3, V:4, or V:5).
ቢ PIP button
Press the PIP button and a sub-picture will appear in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the
last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the four different modes.
POP MODE PICTURE-IN-PICTURE
Press the PIP button and a sub-picture appears in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the
last selection of the PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the PIP CH button to
select between main and sub-picture tuning control (indicated by green highlighted channel display.) Press the VID1, VID2, VID3,
VID4 or VID5 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3,
VIDEO:4 and VIDEO:5 and ANT:A source. (ANT B source cannot be viewed as a sub-picture.)
PIP MODE PICTURE-IN-PICTURE (This feature is only available in 1080i input signal)
To prevent a pattern burn, occasionally move the sub-picture using the THUMBSTICK.
28
PICTURE-IN-PICTURE (PIP)
NOTES: 1. When ANT B is selected as the main channel, the SWAP feature is disabled.
2. In POP mode, thumb stick CURSOR ̆ , ̄ will move the sub-picture up/down.
Ant A 10
Main Picture
Sub Picture
Ant A 10
PIP
Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature
allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The
Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).
ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.
To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. The green highlighted channel
display will move with every press of the PIP CH button. When the top channel display is highlighted, channel tuning is for the main
picture. When the lower channel display is highlighted, channel tuning is for the PIP sub-picture.
The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV
program while viewing other programs from the ANT A source or any of the video inputs.
PIP
ብ,ቦ
ባ
ቤ
ቤ
ቢ
EXIT
M
EN
U
CHVOL
M
U
T
E
PIP PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
VIDEO
REC
SELECT
LAST CH
VCR PLUS+
S
V
C
S
GUIDE/TV
SCHD
V
ID
1
VID 2
VID 3
VID 4
VID 5
CLU-5722TSI
P
B
P
R
CENTER
IN
P
B
P
R
DVI-HDTV
OUTPUT
Audio Video
VCR
ANT A
TO
CONVERTER
ANT B
L
Y
R
(MONO)/L
IR
BLASTER
AUDIO
TO HI-FI
R
S-VIDEO
S-VIDEO
S-VIDEO
Y/VIDEO
R
(MONO)/L
R
(MONO)/L VIDEO
R
(MONO)/L VIDEO
R
L VIDEO
INPUT 1
INPUT 2
INPUT 3
INPUT 4
MONITOR
OUT
AUDIO
AUDIO
AUDIO
PIP
Ant A 10