Filter
Top Products
PLS750C/PLS751C 2/8
5.3 Configuration Menu (Conf)
Use the Configuration menu to set the following parameters (see
sections 5.3.1 to 5.3.4).
5.3.1 Backlight mode (SCRN)
The screen is lit at high intensity for 8 seconds when you press any
button. The rest of the time, depending on the backlight mode
selected, the screen behaves as follows:
Scrn Off: The screen is not lit.
Scrn On HI: The screen is lit at high intensity.
Scrn On LO: The screen is lit at low intensity (default mode).
5.3.2 Automatic Daylight Savings Time Changeover (
DLS
)
When automatic daylight savings time changeover is on (DLS On), the
PLS750C/PLS751C changes to daylight savings time (summer time)
at 2:00 am on the second Sunday of March and changes back to
normal time (winter time) at 2:00 am on the first Sunday of November.
This function is enabled (DLS On) by default.
5.3.3 Latitude and Longitude Coordinates (
LAT and LONG
)
The coordinates are used to turn the lights on at sunset and off at sun-
rise. The latitude is set to +45 and longitude to -75 by default. These
settings provide approximate sunset and sunrise times for most North
American cities. To obtain your city’s coordinates (or those of a nearby
city), see the coordinates table. You can also obtain this information at
www.geonames.org or with a Global Positioning System (GPS)
device. The accuracy of the sunset and sunrise times depends on the
accuracy of the coordinates you enter for your city.
NOTE: Enter a negative value for a south latitude or a west longitude.
5.3.4 Correction Factor (ADJ)
If your city’s time zone is based on political or economic boundaries
instead of its coordinates, your lights might switch on or off too early or
too late with respect to sunrise and sunset. In this case, apply a
correction factor (+1 or -1 hour; refer to addendum). Otherwise, leave
it at 0 (default value).
5.4 Program Menu (Prog)
Use the Program menu to set the programs; i.e. the times you want
the lights to turn On or Off when the switch is in Automatic mode. To
set a program, proceed as follows:
Select a program number (see section 5.4.1)
Set the day(s) of the program (see section 5.4.2)
Set the program start time (see section 5.4.3)
5.4.1 Selecting a program number
You can set up to 21 “On” programs
(“P01 On” to “P21 On”) and 21 “Off”
programs (“P01 Off” to “P21 Off”). For
example, select an “On” program to set
when to turn the lights on; select an
“Off” program to set when to turn the
lights off.
5.4.2 Setting the day(s) of the program
After selecting a program, set the day(s) of the program. You can
select a specific day, all 7 days or “none”. Choose “none” for any
unused program.
5.4.3 Setting the program start time
After setting the day(s) of the program, set its start time. You can
select either a specific time, the sunset time or the sunrise time:
• To select a specific time:
(1) Advance to the hour setting and select the hour.
(2) Advance to the minutes setting and select the minutes.
• To select sunset or sunrise time:
(1) Advance to the hour setting and select the sunset time or
sunrise time. (When you scroll, the sunset time and
sunrise time appear between 11 pm and 12 am.)
(2) To enter an offset (from -70 to +70 minutes in 10-minute
increments) between the sunset or sunrise time and the
program start time, advance to the minutes setting and change
the minutes.
• EXAMPLE: If the sunset time is 6:13 pm and you change the
minutes to display 6:43 pm, you have entered a delay of 30
minutes. If, later in the year, the sunset time is 4:01 pm, the
program will start at 4:31 pm.
• NOTE: When you enter an offset, appears along with
or when you display the sunset or sunrise time. To
remove the offset, display the sunset or sunrise time and
change the minutes until disappears.
5.4.4 Examples
Example 1: The lights turn on at sunset and off at 11:00 pm every day
(default setting).
Example 2: The lights turn on at sunset and off at sunrise every day.
Example 3: The lights turn on at 8:00 pm every day and turn off at
10:00 pm every day except on Saturday night when they turn off at
1:00 am.
Be careful about overlapping!
For example, if you set “P01 Off” at 10:00 pm for all 7 days and set
“P02 Off” to 11:00 pm for Saturday, on Saturday, the lights will turn off
at 10:00 pm, not 11:00 pm since “P01 Off” is set to an earlier time than
“P02 Off”.
When the keypad is locked, the icon appears on the screen and the
only change permitted is the changing of the state. For example, if the
lights are off, they will turn on when you press the main button.
However, in Automatic mode, the default state for the current program
will be overridden until the next program starts. If you press the main
button again before the start of the next program, the lights return to
their initial state. To lock or unlock the keypad, press the buttons
in the following order:
NOTE: You must perform the whole procedure in an interval of 2
seconds. If the procedure was not properly performed, wait another 2
seconds before retrying.
To return the switch to its default settings,
simultaneously press both main and left buttons and
hold. The software version will appear for 5 seconds.
RST will appear for the next 5 seconds. Release the
buttons when all segments appear on the screen. The
switch is now reset (see default settings in the menu
flowchart).
Supply: 120 VAC, 60 Hz
Maximum load: 1800 watts
Operating temperature range: -15 °C to 50 °C (5 °F to 122 °F)
Storage temperature range: -40 °C to 60 °C (-40 °F to 140 °F)
Power outage: The screen is blank. Only the time must be set if the
outage lasts more than 4 hours; all other settings and programs are
permanently saved.
Latitude range: from -65° to +65°
Solar table precision: +/- 11 min. (within ±60° latitude)
Certification: UL (c UL us)
Honeywell warrants this product, excluding battery, to be free from defects
in the workmanship or materials, under normal use and service, for a period
of three (3) years from the date of purchase by the consumer. If at any time
during the warranty period the product is determined to be defective or mal-
functions, Honeywell shall repair or replace it (at Honeywell's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the
place from which you purchased it, or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care
will make the determination whether the product should be returned
to the following address: Honeywell Return Goods, Dock 4 MN10-
3860, 1885 Douglas Dr N, Golden Valley, MN 55422, or whether a
replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty
shall not apply if it is shown by Honeywell that the defect or malfunction was
caused by damage which occurred while the product was in the possession
of a consumer.
Honeywell's sole responsibility shall be to repair or replace the product
within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR
ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDI-
RECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR
IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do
not allow the exclusion or limitation of incidental or consequential damages,
so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL
MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WAR-
RANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE
THREE-YEAR DURATION OF THIS WARRANTY. Some states do not
allow limitations on how long an implied warranty lasts, so the above limita-
tion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights
which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell
Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call
1-800-468-1502.
If you have any questions about your light switch, go to
http://yourhome.honeywell.com, or call Honeywell Customer Care
toll-free at 1-800-468-1502.
“P01 On” “P01 Off”
Program Days Time Program Days Time
P01 On All 7
days
sunset P01 Off All 7
days
11:00
pm
P02 On to
P07 On
None — P02 Off to
P07 Off
None —
Program Days Time Program Days Time
P01 On All 7
days
sunset P01 Off All 7
days
sunrise
P02 On to
P07 On
None — P02 Off to
P07 Off
None —
Program Days Time Program Days Time
P01 On All 7 days 8:00 pm P01 Off Sunday (Su) 10:00 pm
P02 On None — P02 Off Monday (Mo) 10:00 pm
P03 On None — P03 Off Tuesday (Tu) 10:00 pm
P04 On None — P04 Off Wednesday (We) 10:00 pm
P05 On None — P05 Off Thursday (Th) 10:00 pm
P06 On None — P06 Off Friday (Fr) 10:00 pm
P07 On None — P07 Off Sunday (Su) 1:00 am
Keypad Lock
6.
Reset to default Settings
7.
2 sec.
Troubleshooting
8.
The display is faded or
irregular.
The ambient temperature is either below
or above switch’s operating temperature.
The display disappears
when you toggle the
other switch.
Swap the LINE and 3-WAY wires.
The sunset or sunrise
time is inaccurate.
• The date or time is wrong
(see section 5.2).
• The longitude or latitude is wrong
(see section 5.3.3).
• The correction factor is wrong
(see section 5.3.4).
• You have entered an offset
(see section 5.4.3).
Specifications
9.
Warranty
10.
Customer Assistance
11.
69-2504EFS-03 (TI072-3W Honeywell PLS750C_PLS751C).book Page 2 Thursday, September 15, 2011 3:49 PM