Filter
Top Products
Masterpage:Left-FullCol
12 EN
Filename [HM-DH5U_Eng.fm]
INSTALLING YOUR NEW VCR
Connections
NOTES:
• HDMI will be automatically activated (HDMI-ON) when a HDMI connection has been made. To de-activate (HDMI-OFF), press
[HDMI] on the front panel and the [HDMI] LED will turn off.
During HDMI-ON ([HDMI] LED on), the image format output to the TV connected via the HDMI connector will be in accordance to
the image format of the TV. During HDMI-OFF ([HDMI] LED off), the image format output to the TV is in accordance to this VCR’s
“IN/OUT FUNCTION” menu settings “TV OUTPUT 1” and “TV OUTPUT 2” (
A page 65). If the picture cannot be properly
displayed on the TV when using the HDMI to DVI connection, try setting HDMI to OFF.
If your TV is not High-Bandwidth Digital Content Protection (HDCP) compatible, the pictures will not be properly displayed on the
TV. In this case, use the component video, s-video or video connection.
• If you cannot see the pictures on the TV screen when you play back a tape, set “TV OUTPUT 2” to the appropriate mode (A page
65). “TV OUTPUT 2” is invalid when HDMI is activated.
• To operate the VCR with your TV using the HDMI, DVI, Component Video or S-VIDEO connection, set your TV to the AV mode
using the TV’s Remote.
You can also use the TV/VCR button on the VCR’s Remote to set your TV to the AV mode (
A page 76).
• To ensure that you can record one show while watching another (A page 38), you must also connect the VCR to the TV using the
RF cable.
• Use the commercially available i.LINK cable (4-pin, S400, below 3m). If the cable used is above 3m, this VCR will not fully
maximize its performance.
• For full identification of the VCR’s rear panel, refer to the Index (A page 8).
REMOTE PAUSE/
AV COMPULINK
CABLE BOX
VHF/UHF
IN
ANTENNA
ANTENNA
L-2
PCM/STREAM
DIGITAL AUDIO OUT
OPTICAL
PB/CB
PR/CR
Y
COMPONENT
VIDEO OUT
OUTPUT
HDMI OUT
D-THEATER
REGION 1
i.LINK IN/OUT
DV IN
L-1
S400
INPUT
S-VIDEO
VIDEO
L
AUDIO
R
S-VIDEO
VIDEO
L
AUDIO
R
OUT
OUTPUT
S-VIDEO
VIDEO
L
AUDIO
R
DIGITAL IN
AUDIO
VIDEO
R
L
Integrated HDTV
Back of VCR
To 75K terminal
OR
AC Outlet
To [HDMI OUT]
To i.LINK Input/Output Connector
Antenna or Cable
for digital broadcast
i.LINK Cable (not supplied)
To [i.LINK
IN/OUT]
To [HDMI OUT]
HDMI to DVI conversion cable
(commercially available, not
supplied)
When your TV has only DVI input, you can use a commercially
available HDMI to DVI conversion cable to connect between the
VCR and your TV.
To DVI
connector
To Audio Input Connectors
Antenna or Cable
Coaxial Cable
Flat Feeder
Matching Transformer
(not supplied)
To [S-VIDEO OUTPUT]
RF Cable (supplied)
To [ANTENNA
OUT]
To [AUDIO OUTPUT]
To [ANTENNA IN]
(Antenna or cable
input)
To [VIDEO OUTPUT]
To [COMPONENT
VIDEO OUTPUT]
HDMI Cable (not supplied)
S-Video Cable
(supplied)
Video Cable
(not supplied)
Audio Cable
(supplied)
To HDMI
Connector
To S-Video Input
Connector
To Video
Input Connector
Component Video Cable (not supplied)
To Component Video Connectors
HM-DH5U_Eng.fm Page 12 Tuesday, June 1, 2004 4:12 PM
(X:100.0%, Y:100.0%) Created with Grafikhuset CMYK PDF Creator for keiji tanaka at Sanwa Document Services P/L.