Filter
Top Products
Filename [HRJ670EU2.fm]
Masterpage:Left
30
EN
TIMER RECORDING (cont.)
Automatic Satellite
Programme
Recording
This function allows you to automatically record a
satellite programme which is timer-programmed on your
external satellite receiver. Connect a satellite receiver to
the recorder and programme the timer on the satellite
receiver. The recorder starts or stops recording by the
signals input from the satellite receiver. After recording,
the recorder’s power shuts off automatically.
A
Select the L-2 SELECT mode.
Set “L-2 SELECT” to “L-2” or “SAT” (
੬
pg. 39).
●
When you select “SAT”, refer to “IMPORTANT” on page 33.
B
Set the tape speed.
(HR-J670/671/672/673/674/470/
472EU only)
Press
SP/LP
(
p
).
C
Engage the Auto Satellite Programme
Recording mode.
Press and hold
SAT#
for about 2 seconds. The SAT
#
indicator lights up and the recorder turns off
automatically.
NOTES:
●
To disengage the Auto Satellite Programme Recording mode, press
SAT
#. The SAT# indicator goes off.
●
If the recorder’s power is off, it is not possible to engage the Auto Satellite Programme Recording mode.
●
In step
3
, if the SAT
# indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Auto
Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer
Programming” (
੬
pg. 26) to timer-record a satellite programme.
* Some satellite receivers output signals even if the power is off. Auto Satellite Programme Recording is not possible with those satellite receivers.
●
The SAT
# indicator blinks while Auto Satellite Programme Recording is in progress.
●
For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
●
Auto Satellite Programme Recording is not possible if your satellite receiver does not have a timer.
●
Pressing the recorder’s
1 button while Auto Satellite Programme Recording is in progress turns off the recorder’s power and
disengages the Auto Satellite Programme Recording mode.
●
If there are more than one satellite programmes you wish to record with Auto Satellite Programme Recording, it is not possible to set
different tape speeds for each programme.
●
Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may
record slightly longer than the actual length of the programme.
●
If you engage the Auto Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start Auto
Satellite Programme Recording even though the SAT
# indicator blinks. When the satellite receiver shuts off once and is turned back
on again, the recorder starts recording.
●
You can also record a programme from your cable system in the same way if the system has a timer.
●
The B.E.S.T. system (
੬
pg. 23) does not work while Auto Satellite Programme Recording is in progress.
●
Just Clock (
੬
pg. 48) does not work when the Auto Satellite Programme Recording mode is engaged.
●
When the Auto Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Auto Satellite Programme
Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”.
●
After Auto Satellite Programme Recording, the number of recorded programmes will not be displayed on the front display panel for
the Instant ReView function (
੬
pg. 18).
SAT# indicator
ATTENTION
●
Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the recorder will start
recording when the satellite receiver’s power is turned on.
●
If you have connected another appliance other than a
satellite receiver to the AV2 (L-2) IN/DECODER connector,
be sure not to engage the Auto Satellite Programme
Recording mode; otherwise, the recorder will start
recording when the connected appliance’s power is turned
on.
●
Auto Satellite Programme Recording and timer-recording
cannot be done at the same time.
Before performing the following steps:
●
Make sure the satellite receiver is connected to the
recorder’s AV2 (L-2) IN/DECODER connector. (
੬
pg. 33)
●
Programme the timer on the satellite receiver.
●
Insert a cassette with the safety tab in place.
HRJ670EU2.fm Page 30 Wednesday, April 26, 2000 5:22 PM