Filter
Top Products
EN 5
CONFIRM/SET VIDEO CHANNEL
5
If you have connected the video recorder to your TV
via an RF cable only (RF connection)
The channel that is shown on the display panel is your
Video Channel.
To view picture signals from the video recorder, set
your TV to the Video Channel. — Refer to the
instructions supplied with your TV set for how to do
this.
● If you have selected MAGYARORSZAG (36), CESKA
REPUBLIKA (42), POLSKA (48) or OTHER EASTERN
EUROPE (EE) in step 2 on page 4, "2OUT" appears in
stead of "1OUT".
If you have connected the video recorder to your TV
via both an RF cable and a 21-pin SCART cable (AV
connection)
You do not need the video channel so you have to set
the video channel to off.
Press TV PROG – until the display panel shows
"1OUT– –" to set the Video Channel to off.
To view picture signals from the video recorder, set
your TV to its AV mode. — Refer to the instructions
supplied with your TV set for how to do this.
FINISH AUTO SET UP
6
Press OK and refer to page 7 to check the results.
● If "– –:– –" appears on the display panel, refer to
page 7.
SELECT LANGUAGE
3
Press OK. The Language Set display appears on the
front display panel and/or on the screen.
If you are referring to the front display panel
Press
%
fi
to select your language code.
If you are referring to
the on-screen display
Press
%
fi
to move the
highlight bar (pointer) to
the language of your
choice.
PERFORM AUTO SET UP
4
Press OK.
If you are referring to the front display panel
Press
%
fi
to select "Auto" and press OK or
#
.
If you are referring to the on-screen display
Press
%
fi
to move the
highlight bar (pointer) to
"AUTO SET" and press OK
or
#
.
"Auto" blinks on the display panel; do NOT press
any button on the recorder or remote control until
the display panel shows either the display as
illustrated in step 5 or "– –:– –".
● If you are using the on-
screen display, the
AUTO SET screen will
appear. As Auto Set Up
progresses, the " "
mark on the screen
moves from left to
right.
NOTES:
●
Auto channel set function takes place first; it assigns automati-
cally all receivable stations in your area.
●
Auto clock set function sets the clock automatically by
reading the clock setting data from a station transmitting a
PDC signal while auto channel set is being performed.
●
During auto channel set, the recorder recognizes each station
name of the detected stations and stores them in the
recorder's memory, then automatically sets S
HOW
V
IEW
assigned Guide Program number for those stations according
to the broadcast area.
●
In the area where no TV station transmits a PDC signal, the
recorder can perform neither auto clock set nor auto Guide
Program number set.
●
For RF connection users: The video recorder detects the
channels which are not occupied by local stations and selects
one channel automatically for your Video Channel that is
located in the middle of more than 5 vacant channels.
●
If there is a power cut, or if you press or MENU while Auto
Set Up is in progress, Auto Set Up will be interrupted; be sure
to turn off the recorder power once and try again from step 1.
●
Auto clock may not function properly depending on the
reception condition.
AUTO SET
PLEASE WAIT
[MENU] : EXIT
0
+++
Beginning
End
(Ex.) DEUTSCH is selected for SUISSE
(Ex.) DEUTSCH is selected
NÄCHSTE SEITE
NORSK
SVENSKA
NEDERLANDS
CASTELLANO
ITALIANO
FRANCAIS
DEUTSCH
ENGLISH
[
5
∞
] =
[MENU] : ENDE
International telephone
country code
Language code
Language Code
ENGLISH : 01 NORSK : 08
DEUTSCH : 02 SUOMI : 09
FRANCAIS :03 DANSK : 10
ITALIANO : 04 POLSKI : 11
CASTELLANO : 05 E TINA : 12
NEDERLANDS: 06 MAGYAR : 13
SVENSKA : 07
AUTO SET
T-V LINK
[
5
∞
] =
[MENU] : EXIT