Filter
Top Products
Ⅵ
AUTO SP
]LP TIMER —ON/OFF
When this function is set to “ON”, the recorder automatically
switches to LP mode to allow complete recording if there is not
enough tape to record the entire program while timer-recording in
SP mode.
For Example, Recording a PAL-broadcast programme of 210
minutes in length onto a 180-minute tape.
NOTES:
● If you have programed the recorder to timer-record 2 or more
programs, do not use this function, but change the tape speed
manually during timer programing.
● Theremay be some noise andsound disturbancewhere the tape
speedswitchesfromSPtoLPmodeonthetape.
● The Auto SP]LP Timer feature is not available during ITR
(Instant TimerRecording), and thefeature will not work properly
with any tapes longer than E-180 or with some tapes of shorter
lengths.
Multi-Brand Remote Control
This remote control can control some functions of remote
controllable TVs, cable boxes, satellite receivers or DVD sets
listed below. Without setting, you can control a JVC TV.
NOTES:
● Some unit’s brands have more than one code. If the unit does
not function with a specified code, try other codes.
● Depending on the type of unit, some or all functions cannot be
operated using this remote control.
● It’s not possible to operate a unit not equipped with a remote
sensor.
● It’s not possible to set the remote control for two units at the
same time.
● Once you have set the remote control to operate the unit, you
do not have to set it until you replace the batteries from the
remote control.
TV Brand Setting
A
Turn on TV
Turn on the TV using thePower button on the TV or its remote
control.
B
Set TV brand code
A
Press and hold TV.
B
Press the Number keys to enter your TV’s brand code.
C Press OK,andreleaseTV. The TV should turn off.
C
Operate TV
First, press TV to set the remote control to TV mode, then press
one of the following buttons: 1, TV/VCR, TV PR+/–,
^
(TV Muting), TV %+/–,andtheNumber keys.
● Forsome brands, you must pressENTER afterhaving pressed the
Number keys to enter a channel number.
Cable Box, Satellite Receiver or DVD Brand Setting
A
Turn on the unit
Turn on the cable box, satellite receiver orDVD using thePower
button on the unit or its remote control.
B
Enter brand code
A
Press and hold CABLE/SAT/DVD.
B
Press the Number keys to enter your unit’s brand code.
C
Press OK,andreleaseCABLE/SAT/DVD.
C
Operate the unit
First, press CABLE/SAT/DVD to set the remote control to cable
box, satellite receiver or DVD mode, then press one of the
following buttons:
For satellite receiver and cable box . . .
1, TV PR+/–, Number keys.
ForDVD...
1, PLAY (4), STOP (8), PAUSE (9), FF (5), REW (3), we
(26) keys.
● Forsome brands, you must pressENTER afterhaving pressed the
Number keys to enter a channel number.
● To change the unit’s channels, press TV PR+/– or the Number
keys.(ThePR+/– button can be used to change the recorder’s
channels only.)
Approximately 150 minutes Approximately 60 minutes
SP mode LP mode
Total 210 minutes
TV BRAND CODE TV BRAND CODE
JVC
AIWA
BEIJING
CCE
CHANGHONG
DAEWOO
FERGUSON
FINLUX
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JINXING
KONKA
LG/GOLDSTAR
01, 23, 24,25
36
22
02
34
17, 37
27
30
32
15
19
10
28
38
40
18
MITSUBISHI
MIVER
NEC
NOBLEX
NOKIA
PANASONIC
PEONY
PHILICO
PHILIPS
SAMSUNG
SANYO
SHARP
SONY
TCL
THOMSON
TOSHIBA
03
29
20
22
31
04, 11
34, 38, 39
10, 17, 21
02, 42
12, 33, 34,35
13, 16
06
07
41
26
08, 14
– Other Functions –