JVC HR-S2901/2911U VCR User Manual


 
10
Up to 8 timer recording programs can be made using express
timer programing method as far as a year in advance. Remember,
the clock must be set before you can program the timer.
NOTES:
If all the 8 programs have already been set, PROGRAM FULL
appears on the TV screen.
After timer recording is completed, the VCR turns off
automatically.
You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
To timer-record cable or satellite channels, be sure to keep the
cable box or DBS receiver turned on with the correct channel
selected.
Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time, channel settings, and other
menu settings are lost. As a result, when the power is supplied
again to this VCR after the power failure, this VCR starts the
Plug&Play setting automatically to restore the clock time and
channel setting. If the clock time and channel setting are
restored correctly, each timer program you have made will start
at its start time unless its end time has elapsed.
NOTE:
If the tape reaches its end during timer recording, the recording
stops and
#
,
and $ on the display panel blink. Press
TIMER to disengage timer, then press STOP/EJECT (0) on the
VCR to eject the cassette or press POWER 1 then press REW
(3) to rewind the tape.
Express Timer Programing
Load a cassette with the record safety tab intact. The VCR turns
on, and the counter is reset, automatically.
A
Press PROG. on the Remote to access the Program screen.
B
Press START+/, STOP+/, DATE+/ or
CH+/ repeatedly to enter the start
time, stop time, date or channel.
Press and hold START+/ or STOP+/
to increase the time in 30-minute
intervals.
To set the tape speed, press SP/EP.
To timer-record daily (MondayFriday) or weekly serials,
press DAILY (M-F) (Number key 8) or WEEKLY (Number
key 9). Pressing the button again makes the DAILY or
WEEKLY display disappear.
C
Press OK or PROG..
If PROGRAM NOT COMPLETED PROGRAM OVERLAP
appears, see Program overlap warning display (
pg. 10).
D
Press TIMER. The VCR turns off automatically and
#
is
displayed on the display panel.
To use the VCR while it is in timer recording standby
mode
Press TIMER, then press POWER 1. After you use the VCR, press
TIMER again to put the VCR into timer recording standby mode.
Checking, canceling or changing program settings
A
Disengage timer
Press TIMER, then press POWER 1.
When AUTO TIMER is set to ON (
pg. 11), you do not
have to press TIMER.
B
Access Program Check screen
Press PROG. CHECK.
C
Access Program screen
Press PROG. CHECK again. Each time you
press PROG. CHECK, the next programs
Program screen appears.
D
Cancel or change program setting
To cancel a program, press CANCEL when the Program screen
you do not want is shown.
To change a program, press the appropriate button: START+/,
STOP+/, DATE+/, CH+/, DAILY (M-F) (Number key 8),
WEEKLY (Number key 9) and/or SP/EP when the Program
screen on which you want to make changes is shown.
E
Return to normal screen
Press PROG. CHECK repeatedly until no Program screen is
shown.
F
Reengage timer recording standby mode
Press TIMER. The VCR turns off automatically and # is
displayed on the display panel.
When AUTO TIMER is set to ON (
pg. 11), the timer
recording standby mode automatically resumes when you turn
off the VCR.
Program overlap warning display
If PROGRAM NOT COMPLETED PROGRAM OVERLAP
appears, you have another program overlapping the program you
have just made. The Program Check screen appears and
conflicting programs will start blinking.
Example:
Program 1 (you have just made) and Program 4 overlap each other
A
Select program to modify
Press
rt
, then press OK or
e
.
You can only select one of the
overlapping programs.
If you do not mind this overlap, press
PROG. to finish the timer program
setting. The program starting earlier or
program with the lower program number will be recorded.
B
Cancel or change program setting
To cancel a program, press CANCEL when
the Program screen you do not want is
shown.
To change a program, press the
appropriate button: START+/, STOP+/,
DATE+/, CH+/, DAILY (M-F) (Number
key 8), WEEKLY (Number key 9) and/or SP/EP when the
Program screen on which you want to make changes is shown,
then press OK or
e
.
If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
Timer Recording
PROGRAM 1
START STOP
: AM : AM
DATE CH
/ / –– SP
PRESS (+/, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
PRESS (CHECK) TO NEXT
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4
5
6
7
8
( , ) THEN ( ) (PROG.) : END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
( , ) THEN ( ) (PROG.) : END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
PROGRAM 4
START STOP
9:00PM 10:00PM
DATE CH
12/24/02 10 SP
TUE
PRESS (CANCEL) TO CANCEL
PRESS (OK) TO CONFIRM
PRESS (PROG.) TO END