Filter
Top Products
Page 10 July 17, 2003 8:53 am
— 10 —
Other Functions
Checking tape position
When you change the recorder operation
mode from the stop mode to fast forward
or rewind mode, or when you perform an
Index Search or Instant Review, the tape
position indicator appears.
The position of “
q
” in relation to “0”
(beginning) or “+” (end) shows you where
you are on the tape.
● Set “O.S.D.” to “ON” (
੬
11).
Changing display information
Each time you press ––:––, the display panel shows
the channel number and the clock time alternatively.
● You can change display in the stop, recording or
during rewind/fast-forward high-speed search.
● When “O.S.D.” is set to “ON” (
੬
11) and ––:––
on the remote control is pressed, time counter will
appear on the TV screen. To reset the time counter, press 0000
on the remote control.
Function settings
You can use the other useful function settings on the Function Set
screen.
● Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.
A
Access Main Menu screen, then
Function Set screen
Press MENU on the remote control. Press
PR r/t to place the pointer next to
“FUNCTION SET”, then press OK or e.
B
Select Function
Press PR r/t to place the pointer next to
the function you want to set.
C
Change setting
Press OK or e. The default setting is bold in the following table.
Press MENU to return to normal screen.
Ⅵ B.E.S.T. — ON / OFF
When B.E.S.T. (Biconditional Equalized Signal Tracking) system is
set to “ON”, this recorder checks the condition of the tape in use
during playback and recording, and compensates to provide the
highest-possible pictures. This takes place whenever you play
back a tape or start recording after inserting a tape.
N
O
TE:
The recorder checks the tape condition for about 7 seconds, then
starts recording. To make sure you record the desired scene or
program completely, perform the following steps:
A Press and hold 9, and press 7. After about 7 seconds, the
recorder re-enters Record Pause mode.
B Press 4 to start recording.
Ⅵ PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT
This function helps you to adjust the playback picture quality
according to your preference.
AUTO (NORM): Normally select this. Picture quality is adjusted
automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear
instead of “AUTO”.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing much noise.
N
O
TE:
Select “EDIT” when you are editing tapes. After you finish editing
the tapes, select “AUTO”.
Ⅵ PAL/MESECAM — AUTO / PAL / MESECAM
Select the appropriate colour system for recording or playback.
AUTO: Usually set to this mode. The appropriate colour system
(PAL or MESECAM) will be selected depending on the playback or
recording signals.
If the “AUTO” mode does not work properly, select either of the
following manual modes.
PAL: To record PAL signals, or playback a PAL tape.
MESECAM: To record SECAM signals, or playback a SECAM or
MESECAM tape.
N
O
TE
S
:
● SECAM signals will always be recorded as MESECAM. Select
“AUTO” or “MESECAM” when recording SECAM signals.
● When playing back a SECAM tape, select “AUTO” or
“MESECAM”. The playback picture will always be
monochrome.
Ⅵ NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL
To record NTSC signals or playback a NTSC tape, it will be
necessary to select the appropriate mode.
NTSC3.58: To record NTSC signals or playback a NTSC tape.
NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43
tape.
NTSC
]
PAL: To playback a NTSC tape on PAL TV.
N
O
TE
S
:
● The “NTSC]PAL” mode does not work during recording. In
this mode, NTSC signals will be recorded as NTSC3.58.
● The Menu screen is distorted during playing back a NTSC tape
on PAL TV. Stop playback and access the Menu screen again.
● In the “NTSC4.43” mode, with some TVs, on-screen displays
(Program screen, etc.) may roll up or down and there may be a
loss of colour. When this happens, select the “NTSC3.58”
mode.
1:23:45
0
+++ +
[ / ]
[MENU] : EXIT
MAIN MENU
FUNCTION SET
TUNER SET
INITIAL SET
[ / ]
[MENU] : EXIT
FUNCTION SET
B.E.S.T. ON
PICTURE CONTROL AUTO
PAL/MESECAM AUTO
NTSC NTSC3.58
AUTO TIMER OFF
O.S.D. ON
AUTO SP LP TIMER OFF
HR-V400AG-EN.fm Page 10 Thursday, July 17, 2003 8:53 AM