Filter
Top Products
Page 6 November 17, 2000 12:37 pm
Setting channels manually
— Manual Channel Set
You can add the channels you want or delete the channels you do
not want manually.
A
Access Main Menu screen, then Tuner
Set screen
Press MENU on the Remote. Press
rt
to
move the highlight bar (arrow) to “TUNER
SET”, then press OK or
e
.
B
Access Manual Channel Set screen
Press
rt
to move the highlight bar
(arrow) to “MANUAL CHANNEL SET”,
then press OK or
e
.
C
Add or skip desired channels
To add channels
A Press the Number keys on the Remote
to input a channel number you want to
add.
B Press OK or
e
to set to “ADD”.
C Repeat A to B to add other channels.
Press MENU to return to normal screen.
To skip channels
A Press
rt
or the Number keys to select a channel number you
want to skip.
B Press OK or
e
to set to “SKIP”.
C Repeat A and B to skip other channels. Press MENU to return
to normal screen.
Cable Box and/or DBS Receiver Control
Setting
The following procedure is required if you receive your TV
channels through a cable box (descrambler) and/or if you receive
satellite channels through DBS (Direct Broadcast Satellite)
receiver. The Controller allows the VCR to automatically switch
the cable box or DBS receiver’s channel during timer recording.
NOTES:
● The Controller is not supplied with this unit. It can be requested
by mailing in the completed JVC Cable Mouse Certificate that is
included with the accessory package.
● For the cable box, the Controller is effective for VCR Plus+ or
Express timer programing.
● For the DBS receiver, the Controller is effective only for Express
timer programing.
● When connecting your cable box or DBS receiver, refer to its
instruction manual.
A
Situate Controller
If both a cable box and a DBS receiver are used, position the
Controller so its signal reaches the remote sensors on both the
cable box and DBS receiver.
B
Attach Controller
Fix securely using the adhesive strip attached on the back of the
Controller.
C
Connect cable box and/or DBS receiver to VCR
● If your cable box or DBS receiver does not have audio/video
output connectors, connect the RF output terminal on the unit
to the ANT. IN terminal on the rear of your VCR.
● If your cable box or DBS receiver has audio/video output
connectors, connect an audio/video cable between the AUDIO/
VIDEO IN connectors on the rear of the VCR and the audio/
video output connectors on the unit.
● If both a cable box and a DBS receiver are used, it is
recommended that you connect the DBS receiver to your VCR’s
AUDIO/VIDEO IN connectors and the cable box to your VCR’s
ANT. IN connector.
D
Connect Controller to VCR
Connect the Controller to the CABLE BOX Controller connector
on the rear panel.
E
Turn on cable box or DBS receiver
Select a channel other than channel 9 on your cable box, or
channels 55, 100, 205 on your DBS receiver.
F
Access Main Menu screen, then Initial Set screen on VCR
Press MENU on the Remote. Press
rt
to move the highlight bar
(arrow) to “INITIAL SET”, then press OK or
e
.
G
Access Cable Box Set screen or DBS
Receiver Set screen
Press
rt
to move the highlight bar
(arrow) to “CABLE BOX SET” or “DBS
RECEIVER SET”, then press OK or
e
.
H
Select output channel
Your selection depends on how the unit is
connected to your VCR.
● If the unit is connected to your VCR’s
ANT. IN terminal on the rear panel,
Press
rt
until the channel number
representing the cable box’s output (CH2
– CH9) or DBS receiver’s output (CH3 or CH4) appears on the
screen.
● If the unit is connected to your VCR’s AUDIO/VIDEO IN
connectors on the front panel, press
rt
until “ON F-1
(FRONT)” appears on the screen.
● If the unit is connected to your VCR’s AUDIO/VIDEO IN
connectors on the rear panel, press
rt
until “ON L-1 (REAR)”
appears on the screen.
● If you do not use any unit, press
rt
until “OFF” appears on
the screen.
I
Access Brand Set screen
Press OK or e.
● If the Clock Set screen appears, perform “Manual Clock Set”. If
you press MENU after the clock has been set, the Brand Set
screen appears.
MAIN MENU
FUNCTION SET
TUNER SET
INITIAL SET
PRESS ( , ), THEN (OK)
PRESS (MENU) TO END
TUNER SET
BAND CATV
AUTO CHANNEL SET
MANUAL CHANNEL SET
SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END
MANUAL CHANNEL SET
(CATV)
CH 45 ADD
PRESS NUMBER KEY (0–9)
OR ( , ), THEN (OK)
PRESS (MENU) TO END
Your VCR
Cable box or DBS receiver
Controller
(suggested locations)
Transmitter
Controller
Cable box or DBS receiver
To ANT. IN
To AUDIO/VIDEO IN
RF out Audio/video output
VCR
SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END
INITIAL SET
CLOCK SET
LANGUAGE ENGLISH
GUIDE CHANNEL SET
CABLE BOX SET
DBS RECEIVER SET
PRESS ( , ) THEN (OK)
PRESS (MENU) TO END
CABLE BOX SET
OFF
– Initial Settings –
HR-VP790U-EN.fm Page 6 Friday, November 17, 2000 12:37 PM