Filter
Top Products
Changing the initial settings
28
XV-NK38SL/GNT0028-003A/English
Chang
ing the
init
ial settings
SCREEN SAVER
You can set the screen saver function to ON or OFF. (See page
10.)
Setting options
ON, OFF
AUDIO menu
DIGITAL AUDIO OUTPUT
To connect the unit’s digital output to an external device equipped
with a digital input, this item must be set correctly.
See “Appendix C: Digital output signal chart” on page 38 for
details about the relation between the setting and output signals.
Setting options
PCM ONLY, DOLBY DIGITAL/PCM, STREAM/PCM
[PCM ONLY]: select when you connect the DIGITAL OUT jack of
the unit to the linear PCM digital input of other audio
equipment.
[DOLBY DIGITAL/PCM]: select when you connect the digital
input of a Dolby Digital decoder or an amplifier with a built-in
Dolby Digital decoder.
When this option is selected, playing back a disc recorded by
the MPEG Multichannel format outputs a linear PCM digital
signal.
[STREAM/PCM]: select when you connect the digital input of an
amplifier with a built-in DTS, MPEG Multichannel or Dolby
Digital decoder, or the stand-alone unit of such a decoder.
• With some DVD VIDEO discs that are not fully copy-protected,
a 20 or 24 bit digital signal may be output.
• A signal recorded with the 96 kHz or higher sampling frequency
is output from the DIGITAL OUT jack with the 48 kHz sampling
frequency.
• The unit does not provide the DTS decoding function.
• When playing a DVD VIDEO or Audio CD disc with DTS, use a
DTS decoder to get correct signals from your speakers.
• DTS-encoded signal is output only from the unit’s DIGITAL OUT
jacks.
• If the unit is not connected to audio equipment with a DTS
decoder, DTS-encoded signal output from the DIGITAL OUT
jacks is distorted.
ANALOG DOWN MIX
To correctly play the audio on a DVD VIDEO disc recorded with
surround multichannel audio, you must set this item properly
according to your audio system configuration.
(This function does not work when the 3D PHONIC function is
activated.)
Setting options
DOLBY SURROUND, STEREO
[DOLBY SURROUND]: select when listening to multichannel
surround audio with the unit’s analog AUDIO OUT terminals
connected to a surround decoder.
[STEREO]: select when listening to conventional two-channel
stereo audio with the unit’s AUDIO OUT terminals connected
to a stereo amplifier/receiver or television set, or in case you
want to record the audio from a DVD VIDEO disc to MiniDisc,
cassette, etc.
D. RANGE CONTROL
This setting provides optimal audio quality from the analog
AUDIO OUT terminals for listening to DVD VIDEO discs recorded
in Dolby Digital format, at low or middle volume.
Setting options
WIDE RANGE, NORMAL, TV MODE
[WIDE RANGE]: when selected, audio is played back with the
widest dynamic range so that you can enjoy powerful
playback sound.
[NORMAL]: normally, select this option.
[TV MODE]: select if DVD VIDEO disc sound level is lower than
TV program sound level. Thus you can hear sound at a lower
volume clearly.
OUTPUT LEVEL
This setting allows you to attenuate the level of the signal output
from the unit’s analog AUDIO OUT terminals.
Setting options
STANDARD, LOW
• If the sound output from the speaker is distorted, select [LOW].
OTHERS menu
RESUME
You can select the resume playback mode.
See pages 8 and 9 for details about the resume playback
function.
Setting options
ON, OFF, DISC RESUME
[ON]: when selected, the unit can resume playback of the disc
from the position where playback was last interrupted, if the
disc is still in the disc tray.
[OFF]: when selected, the resume function is deactivated.
[DISC RESUME]: when selected, the unit can resume playback
of the last 30 discs played. The unit retains a memory of the
interrupted positions of the last 30 discs played, even though
they have been removed from the disc tray.
ON SCREEN GUIDE
The unit can display “on-screen guide” icons or characters on the
picture, which show what is happening to the disc or the unit.
Example of “on-screen guide” icons: , ,
Setting options
ON, OFF
[ON]: when selected, the on-screen guide is activated.
AUTO STANDBY
When the unit is stopped for more than 30 minutes or 60 minutes,
the unit enters standby mode automatically.
Setting options
60, 30, OFF
AV COMPULINK MODE
You must set this item correctly to use the AV COMPULINK
system.
Setting options
DVD1, DVD2, DVD3
• See page 33 for details about the AV COMPULINK function.
XVNK38SL(USUBUGUX).book Page 28 Friday, May 9, 2003 7:36 PM