Filter
Top Products
3
RC-R0507 (En/T)
Remote Control
Input Component Maker Code Key
(CD) CD player KENWOOD 8028, 8037 AUDIO
TV 1
TV 2
CABLE
The remote control supplied with this receiver is also
capable of controlling components from a variety of manu-
facturers once you register the appropriate setup codes
into the remote control unit.
Refer to "Remote operation of other components" for de-
tails about the operations available for each component.
1
Registering setup codes for other components
Find the setup code of the component to be registered.
Getting the most from your remote control
•Refer to the setup code lists to find the setup code for the
component to be registered. RC7
Example: To register a CD made by KENWOOD, you would enter
"8028".
•When registering setup codes for KENWOOD audio components
which are connected to this unit by system control cords, use the
following codes to insure proper system control operation:
Cassette: 7000, CD: 8099, MD: 9000.
2
3
Hold down the ENT key until the backlight flashes twice.
Press the VIDEO, AUDIO, or TV key repeatedly to select
the desired component.
•At this time all inputs become available regardless of any earlier
registration.
•Example : To register the component connected to the VIDEO 1
jacks, select "VIDEO 1 (VCR1)".
•On models other than the KRF-V8010D, “DVD 6ch” is displayed
instead of “VIDEO 3”. It is possible to enter a setup code for the
DVD 6ch input, but the display indication will remain “DVD 6ch”.
It is not possible to change the name of this input.
VIDEO key
1VIDEO1 (VCR1)
2VIDEO2 (VCR2)
3VIDEO3 (DVD)
or DVD 6ch
AUDIO key
1CD (CD)
2TAPE or MD
(TAPE)
3PHONO
TV key
1TV1
2TV2
3CABLE
Low battery warning
Replace all four batteries with new ones when you notice a shortening
of the distance from which the remote control will operate or if the
remote control blinks 5 times when you press a key. The remote
control is designed to retain setup codes in memory while you
change batteries.
4
Use the numeric keys to enter the setup code.
5
Press the POWER key, and check to see that the compo-
nent you want to control turns on.
7
Repeat steps 3 to 6 to register additional components
until all components have been registered.
6
Press the ENT key to store the code you have just input.
•Example: Press "5258" to register a LD player made by KENWOOD.
•The backlight flashes once each time a number is entered.
•If an invalid setup code is entered the remote will output one long
blink, disregard that code and return to the beginning of step 4.
•If you push an invalid key, the remote will exit the setup mode.
•The backlight flashes twice.
•This code replaces any previous setup codes entered for the
respective component.
If the component does not react, and there is more than one
setup code, enter another setup code and try again.
•PLAY, TUNING/SKIP (+/–) or MULTI CONTROL key can also be
used instead of POWER key.
• If the component is already on, pressing POWER key will turn it off.
•If you have components that are not remote controllable, like a
record player (etc.), you will need to register a Non-IR code at the
respective input. This keeps the respective input in the remote
control's cyclic list so you can select it using the remote control.
Please consult the owner's manual of the components you are
connecting for information regarding remote controllability. The list
of Non-IR codes is included at the beginning of the Setup code
chart.
ENT
VIDEO, AUDIO, TV
POWER
1-0
For step 2 through step 8, make sure you start the next step
within five seconds of completing the previous one. If more
than five seconds elapses between any two steps, you will
need to go back and start over from step 2.
V
CR1
A
SP
SW
R
L
Continued to next page