Filter
Top Products
103
4a. Select ChannelPair ......................... [1 2…15 16]
Press the “1 2”–“15 16” button for the channels
that you wish to pair. When pairing is “On,” the
heart icon will be displayed.
4b. Select Function....................[Eq, Send, Aux, Pan]
Select the functions that will be paired for the chan-
nels selected by “Select ChannelPair.”
For the functions “EQ”–“Pan” that you wish to pair,
press the button to enable pairing (the button will
be highlighted). The settings will be applied when
you press the “OK” button.
When pairing is on, the pairing function will
always apply to the fader and track status.
P2 Ch9–16: Select the inputs for
mixer channels 9–16
Here you can select the inputs for mixer channels 9–16.
Refer to “P1 Ch1–8: Select the inputs for mixer channels
1–8.”
P3 InEq1–4: EQ settings for inputs
1–4
Here you can apply EQ (equalizer) to the analog inputs
from the [INPUT 1]–[INPUT 4] jacks. Make these set-
tings when you wish to directly record the sound that is
adjusted by the EQ.
The EQ has three bands. High EQ and low EQ are
shelving type, and the mid EQ is a peaking type with
adjustable cutoff frequency.
This EQ cannot be used on the digital input (S/P
DIF IN) or on the rhythm.
1. InputLevelMeter .......................................................
(1, 2, 3, 4/CLP, –6, –12, –18, –40dB)
This shows the level of each analog input.
The horizontal axis indicates the channel, and the
vertical axis indicates the level.
Inputs that are not selected in “Ch1…8” ([INPUT]
P1-1) will not be displayed.
2. InputHigh.................. [(Fc=10kHz)–15.0…+15.0(dB)]
Set the input high EQ gain. This adjusts the high-
frequency range.
You can cut/boost over a range of –15.0 – +15.0 dB
at a 10 kHz cutoff frequency.
3. InMidFc.....................................[100Hz…20.0k(Hz)]
Set the cutoff frequency for the input mid EQ.
This can be adjusted over the range of 100 Hz–20.0
kHz.
4. InputMid.................................... [–15.0…+15.0(dB)]
Set the input mid EQ gain.
This adjusts the mid-frequency range. You can cut/
boost over a range of –15.0 – +15.0 dB at the cutoff
frequency specified by “InMidFc.”
5. InputLow ...................[(Fc=100Hz)–15.0…+15.0(dB)]
Set the input low EQ gain. This adjusts the low-fre-
quency range.
You can cut/boost over a range of –15.0 – +15.0 dB
at a 100 Hz cutoff frequency.
6. Pair........................................................................
Enable pairing for adjacent mixer channels. (→p.102
“Pair”)
P4 InEq5–8: EQ settings for inputs
5–8
Apply EQ (equalizer) to the analog input from the
[INPUT 5]–[INPUT 8/GUITAR IN] jacks.
Refer to “P3 InEq1–4: EQ settings for inputs 1–4.”
P5 Tuner: Tuner
You can use the built-in tuner to tune an instrument
connected to the [INPUT 8/GUITAR IN] jack. You can
also determine the pitch of a track.
This page cannot be selected during recording or
playback. Nor is recording possible.
In order to allow accurate tuning, the insert effects
and master effects will automatically be turned off
when this page is displayed.
1. CENT Scale ............................................ (–50…+50)
The “ ” symbol in the center will change to “▼”
when the tuning is correct. The amount of pitch
deviation is shown in units of cents (100 cents = 1
semitone, and 1200 cents = 1 octave)
2. NoteDisplay................................................... (C…B)
This shows the name of the note that is closest to the
input sound.
It is not possible to detect the pitch if two or more
notes are played simultaneously.
3. Calib ....................................... [435…440…445Hz]
Specify the frequency that will be the basis for tun-
ing. Normally you will set this to “440.”
4. SelectSource ....................... [Input8, Track No1…16]
Input8: Select this when you wish to tune an exter-
nal device such as a guitar, or when using the built-
in mic to tune.
Track No “1…16”: Select the track whose pitch you
wish to measure. Move to the time location that you
1
324
5
6
3
1
4
2
Reference
INPUT