Filter
Top Products
102
P1 Ch1–8: Select the inputs for
mixer channels 1–8
Here you can select the inputs for mixer channels 1–8.
(→p.23)
1. Ch1...8...................................................................
[Input1…8, S/PDIF L, R, Rhythm L, R, CD L, R*]
Select a channel icon “Ch1”–“Ch8,” and select the
source that will be input to each channel.
INPUT1…8: The analog output from an instrument
connected to the [INPUT 1]–[INPUT 8/GUITAR IN]
jacks will be input to the channel.
S/PDIF L, R: The digital output from a DAT con-
nected to the [S/P DIF IN] jack will be input to the
channel. This can be selected when “DigiIn” is
“On.”
Insert effects cannot be used on the digital
input.
Rhythm L, R: The rhythm selected by “SelRhythm”
(→p.95) will be input to the channel. During record-
ing/playback, the rhythm will be heard regardless
of the “Rhythm” (→p.95) “On/Off” setting. This
rhythm can be recorded. (→p.61)
CD L, R: if an optional CDRW-2 is installed, the cor-
responding channel of an inserted audio CD can be
input to a channel.
* CD L, R can be selected only if the optional
CDRW-2 is installed.
* The audio of the internal CD-R/RW drive is con-
nected as an analog signal.
2. DigiIn ........................................................[On, Off]
Turn this “On” if you wish to use the digital input
(S/PDIF IN).
When you press the “DigiIn” button, a message of
“Obey Copyright Rules” will appear. Carefully read
the owner’s manual section “COPYRIGHT WARN-
ING” (→p.1). If you accept the terms, press the
“Yes” button in response to the “AreYouSure?”
prompt. Digital input will be enabled.
On: “S/PDIF L” or “S/PDIF R” can be
selected for “Ch1…8.”
When this is “On,” insert effects cannot be
used.
Off: “S/PDIF L” or “S/PDIF R” cannot be
selected for “Ch1…8.”
3. SubIn......................................................................
Make these settings when you wish to use the
inputs as “sub inputs” for inputting the return from
an external effect to the [INPUT 1]–[INPUT 8/GUI-
TAR IN] jacks, or so that the sound of an instrument
connected to these jacks can be mixed with the track
playback. (→p.50)
After completing a song on the D1600, you can syn-
chronize a sequencer to the D1600 and use sub
inputs to mix the sequenced sounds with the track
playback of the D1600.
These inputs are sent via the stereo/mono switch
through the balance and fader settings, and then to
the master LR bus.
Use the [AUX OUT] jack to transmit the effect send
to your external effect processor. (→p.108 [MASTER
EFFECT/AUX] “AuxSend” tab page)
3a. Stereo/Mono............................... [Stereo, Mono]
Stereo: Odd-numbered channel inputs will be
sent to the master L bus, and even-numbered chan-
nel inputs will be sent to the master R bus.
Mono: Odd-numbered and even-numbered
channel inputs will be summed, and the same sig-
nal will be sent to the master L bus and R bus.
Use this when the input is received on only one
channel.
If the sound distorts when this is set to
“Mono,” adjust the level on the input device or
using the [TRIM] knob.
3b. Balance...................................[L63…CNT…R63]
Adjust the balance for when the sub input is sent in
stereo to the master LR bus.
3c. Fader ...............................................[000…100]
Adjust the amount of sub input signal that is sent to
the master LR bus.
3d. Mute....................................................[On, Off]
On: The sub input will be muted; it will not be
sent to the master LR bus.
Off: The sub input will not be muted; it will be
sent to the master LR bus.
4. Pair ........................................................................
This lets you pair adjacent mixer channels.
Press the “ ” button to access the following screen.
Channels that are paired will be controlled by the
knobs and fader of the odd-numbered channel.
Operating the knobs or fader of the even-numbered
channel will not control anything.
17. INPUT
2
3
1
4
3a
3b
3c
3d
4a
4b