Filter
Top Products
93
The mixer settings that you adjust can be registered at a
desired time location as a Scene, and used to automati-
cally change the mixer settings as the song plays (when
“SceneRead” is turned “On”). Scenes can also be used
as general-purpose settings, and recalled and used
when desired. (→p.39)
Up to 100 scenes can be registered in each song.
The following settings can be registered in a scene.
MixerChannel
EQ, EffectSend1, 2, AuxSend, Pan/Balance, ChFader,
PairOn/Off
InsertEffect (only when Assign is “Trk”)
EffectType, InsertTo, EffectNumber
MasterEffect
EffectNumber, EffectReturn
FinalEffect
EffectNumber
Filters are provided for each of these parameter groups,
allowing you to select whether or not they will be regis-
tered or recalled (→”Filter”).
P1 ReadDel: Scene playback on/
off and editing
1. SceneRead ................................................ [On, Off]
Turn scene playback on/off.
On: Scene playback is enabled.
During playback, each scene will be recalled when
its registered time is reached, and the mixer settings
will change automatically.
When this is “On,” the [SCENE] key will light.
Off: Scene playback is disabled.
You can freely recall scenes as general-purpose set-
tings without regard to their time location. (→p.40
“Recalling a scene”)
2. Filter .......................................................................
You can use filters to disable changes for specified
mixer settings (parameters) when registering or
recalling scenes.
Here you can select which mixer settings (parame-
ters) will be disabled.
On: The filter will be on for that channel/parame-
ter, and the scene settings will be disabled.
Off: The filter will be off, and the scene settings will
be enabled.
When you register a scene, the filter settings act as a
registration filter for that song.
Use the filter while registering if you wish to pre-
serve some of the settings from the previous scene.
For example, suppose that you turned the filter
“On” for the “Pan” of channels 1 and 2, and regis-
tered the current settings as scene “002” in the mid-
dle of the song. Then for playback, suppose you
turned the “EQ” filter “On.”
Turn on scene playback and play back from the
beginning of the song. When playback reached the
location of scene “002,” pan will remain at the set-
tings of scene “001” (registered at the beginning of
the song), since scene “002” does not contain pan
settings. Other settings will change to the values of
scene “002.” Since EQ is being played back through
the playback filter, the values registered in the
scenes from the beginning of the song will not be
used; the current EQ settings will be maintained.
3. SceneNumber........................................[001…100]
This recalls the mixer settings of a scene to the cur-
rent time location.
This is also used to recall a scene when you wish to
modify its name or to change its time location.
The time location at which the scene is registered is
shown beside “SceneNumber.”
If “SceneRead” (P1-1) is “Off,” you can select any
desired scene. If this is “On,” the scene for the cur-
rent time will be selected, and cannot be chosen
manually.
4. Sort........................................................................
Sort scenes in order of time.
Normally, scenes are arranged in the order in which
they were registered, but you can sort them in
ascending order of registered time.
Undo is not available after executing Sort.
5. Rename..................................................................
This lets you modify the name of a scene.
Use “SceneNumber
” to recall the scene whose name
you wish to modify, press the “Rename” button to
access the dialog box, and modify the name. A
name of up to sixteen characters can be used.
(→p.21)
If the [SONG] “SelSong” tab page item “Select Disp-
Parameter” is set to “Scene,” the scene name will be
displayed in that page. (→p.88)
8. SCENE
1
7
10
8
4 5 3
2
6
9
Reference
MARKSCENE STORE