LG Electronics 22LG3DCH CRT Television User Manual


 
23
206-4096
078 - UPN MSB (UPN Most Signi cant Byte)
User programmable number, most signi cant byte readable by
MPI command. Not linked to serial number.
079 - UPN MSB-1 (UPN Most Signi cant Byte-1)
User programmable number, most signi cant byte-1 readable by
MPI command. Not linked to serial number.
080 - UPN MSB-2 (UPN Most Signi cant Byte-2)
User programmable number, most signi cant byte-2 readable by
MPI command. Not linked to serial number.
081 - UPN LSB (UPN Least Signi cant Byte)
User programmable number, least signi cant byte readable by
MPI command. Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid MPI checksum validation. Set to 1 for validation.
Set to 0 to disable (does not check checksum on MPI async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing MPI timing requirements to be compatible with PC-
based Windows controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent
by disabling the blocking hours function. Set to 1 to install Paren-
tal Control restrictions permanently. Set to 0 for user-speci ed
hours control of blocking schemes.
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV. Set to 0 to disable RGB
input. Set to 2 (LG3DCH) / 1 (LG3DDH) to enable for RGB PC
input. Set to 18 (LG3DCH) / 17 (LG3DDH) to initiate a one-time
automatic con guration after an AC power cycle; otherwise,
automatic adjustment will be performed each time the RGB input
is accessed.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
090 - KEY LOCK
If set to 1, front keyboard Channel, Volume, and Captions buttons
are disabled, Power button remains enabled. If set to 0, the Chan-
nel, Volume, Captions, and Power buttons are all enabled.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function menu, if Function
Menu is available. Set to 0 to disable SAP feature on Function
Menu, if Function Menu is available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up.
Set to 0 for Set By System.
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 3 for Just Scan. (LG3DDH only)
Set to 4 for Zoom. (Zoom 1 for LG3DCH)
Set to 5 for Zoom 2. (LG3DCH only)
Note: Only applies if item 106 ASP RATIO LOCK is disabled, set
to 0.
099 - BACK LIGHTING
Sets the TV screen brightness at power up.
LG3DCH: Default setting is 100. LG3DDH: Default setting is 200.
1 - 100 Static Back Lighting
(1 = Dimmest picture, 100 = Brightest picture)
101 - 200 Dynamic Back Lighting
(101 = Dimmest picture, 200 = Brightest picture)
If settings are above 200, the TV automatically controls back light-
ing depending upon the picture level of the current program.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode: Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for Normal. Set to 1 for Blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal. Set to 1 to load presets of all Installer Menu
item settings. Setting this item to 1 will also reinitiate the Express
Script Installer Menu Wizard (see pages 16 – 17).
Warning: If set to 1, this will reload the factory
defaults and clear the Channel List, including any
assigned channel icons and custom channel labels.
Installer Menu (Cont.)