Filter
Top Products
CODING
Before you begin to use your MULTI-CODE RECEIVER YOU
MUST SET THE CODING SWITCH. In order to set the code,
refer to figure 2.
To gain access to the switch, remove the top section of the
cabinet, if you have not already done so, Using a pencil, or
other similar device, move the code switches to set your
house code. Positions one through nine on most MULTI-
CODE transmitters are used to set the house code.
NOTE:
THE MULTI CODE 4120 TWO CHANNEL TRANSMITTER OR
4140 FOUR CHANNEL TRANSMITTER REQUIRES A DIF-
FERENT CODE SELECTION. REFER TO THE APPROPRIATE
INSTRUCTIONS IF THERE IS ANY DOUBT AS TO CORRECT
SETTING.
Setting code switch 10 on your transmitter will determine
channel one or channel two. If the number 10 DIP switch is
set in the OPEN or OFF position, you have channel one, if
the second channel is desired, then set the transmitter DIP
switch number 10 to the CLOSED or ON position.
We strongly urge that you avoid the following code
schemes: ALL ON, ALL OFF, 2 4 6 8 on 1, 3, 5, 7, 9 on.
These codes are frequently used by other manufacturers,
and create the possibility of false operation, and may be
less secure than other code arrangements.
BE SURE TO SET THE FIRST NINE SWITCHES ON YOUR
RECEIVER EXACTLY THE SAME AS THE TRANSMITTER.
Be certain to check that each code is functional before com-
pleting the installation.
ADDITIONAL INSTALLATION INFORMATION
LINEAR CORPORATION has taken every possible precau-
tion to make the 3021 Receiver as reliable as possible. The
circuit board is coated with a special water resistant treat-
ment. We think the following notes should be observed:
•
Be sure the unit is sealed from moisture, and, if at all
possible, keep it away from direct moisture.
•
If you are using the 3021 Receiver, make sure the seal
around the top of the cabinet and that the strain relief
of the 3021 prevents moisture from entering.
•
In those installations where vibration may be a factor,
be sure to use a fastening compound, such as LOC-
TITE
on the mounting screws to insure reliable
mounting.
•
If this, or any other equipment is being used in a safety
related device, be sure to test the entire system at the
time of installation, and at frequent intervals, to deter-
mine that it is working properly.
OPERATION
We urge you to test your installation completely before
putting it into operation. Testing this receiver with the rest
of the system will save potential problems later on.
Note that two channels will not receive at the same time.
Each channel requires a distinct signal from a transmitter in
order to become activated.
WARRANTY
ALL MULTI-CODE garage door related products carry a eighteen (18)
month warranty against defects in workmanship or material. This war-
ranty begins at the date of manufacture, for eighteen months. LINEAR
CORPORATION warrantees our product only to our authorized dealers
and distributors, and not to the end customer. If you have any questions
about our warranty, please ask your dealer to determine the nature and
scope of his warranty. LINEAR CORPORATION does not assume, and
is not responsible for, any real or consequential damages from claims
against the performance of our product, nor is it liable for any costs
related to loss of life, property, or revenue. Further, LINEAR CORPO-
RATION is in no way responsible for installation of our product, and will
assume no costs to reinstallation or removal.
LINEAR CORPORATION’S Warranty is in lieu of all other warrantees,
expressed, or implied.
Please Note
LINEAR CORPORATION has devoted a great deal of time and research in
order to provide the most reliable equipment possible. Certain limitations
must be observed:
1.
MULTI-CODE radio components must conform with FCC Part
15 requirements. For this reason, the range and power of
our radios is within specified limits
2.
As with all manufacturers, MULTI-CODE radios must accept all
signals that they receive. This may, in rare instances, create difficulty.
3.
You should test your entire system occasionally in order to be
sure that all components are working in good order.
4.
MULTI-CODE dealers can provide you with information regard-
ing the use of our radio controls, and can provide valuable
installation and operation information, when requested.
5.
Any changes or modification in intentional or unintentional radia-
tors which are not expressly approved by Linear Corporation
could void the user’s authority to operate this equipment. This
applies to intentional and unintentional radiators certified per part
15 of the F.C.C. rules and regulations.
Copyright © 1999 Linear Corporation 214791 B
INSTR,INSTL,MC3028,2CH,RCVR
LINEAR P/N: 214791 B
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 10.000" x 8.000"
SCALE: 1-1
SIDE 2 OF 2
1 2 3 4 5 6 7 8 9
O
N
O
F
F
FIGURE 2