Loewe 32 HD, 32HD/DR Flat Panel Television User Manual


 
23
TV menu
Standard settings
Sound
zap2text
Picture
Connections
Settings
Rotate TV
Sound
Loudspeaker sound
Headphone sound
AV audio signal
Dig. DVB output tone
Headphone volume
Sound via TV AV amplifier (digital input) HiFi Concertos
AV settings
Allow swichting voltage
Manual adjustment of AV standard
Assign audio digital
RGB insertion at AV2
120-240V
50/60Hz
SERVICE
IR-
Link
SYSTEM
ANT-1
ANT-2
PIP
UHF/VHF
AUDIO
IN 2
Y
IN1
AUDIO IN1
L R
AV 2 ( RGB )
Center Sub
L R
SOURROUND
DVI-INPUT
D-SUB
DVI-OUTPUT
CONTROL
RC5/
RC6
VGA
DISPLAY
DIGITAL
L R
AUDIO IN 3
L R
AUDIO OUT
C
R
/P
R
C
B
/P
B
IN2 OUT
AV 1
S-VIDEO OUT
DIG OUT
REAR
MAINS
L
R
(CVBS) (Y/C)
VIDEO OUT
AUDIO
STEREO OUT VIDEO OUT
I
AUX-
I
/O
II
TO TV-
I
/O
OPT OUT
RIGHT SUBW.
REAR
RIGHT
FRONT
LEFT CENTER
MULTICHANNEL AUDIO OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
LEFT
FRONT
In
Out
VIDEO
OUT
AUDIO OUT
R L
DIGITAL OUT
COAXIAL
TO TV
S-VIDEO
OUT
VIDEO
OUT
AUDIO OUT
R L
DIGITAL OUT
COAXIAL
TO TV
S-VIDEO
OUT
DVD 1
DVD 2
120-240V
50/60Hz
SERVICE
IR-
Link
SYSTEM
ANT-1
ANT-2
PIP
UHF/VHF
AUDIO
IN 2
Y
IN1
AUDIO IN1
L R
AV 2 ( RGB )
Center Sub
L R
SOURROUND
DVI-INPUT
D-SUB
DVI-OUTPUT
CONTROL
RC5/
RC6
VGA
DISPLAY
DIGITAL
L R
AUDIO IN 3
L R
AUDIO OUT
C
R
/P
R
C
B
/P
B
IN2 OUT
AV 1
OK
OK
OK
OK
OK
OK
Assign audio digital
Digital In1 no to AV1 to AV2 to AVS
Digital In2 no
Operating additional equipment
Digital input/output
Have you logged in your video equipment, e.g.
DVD players or VCRs in the ”TV menu–
Connections” as described on page 21?
For analog picture and sound signals from the
VCR or DVD player, use a Euro-AV cable to
connect the Euro-AV socket 1 or 2 to the Signal
Box and the corresponding AV socket of the
VCR.
The Signal Box also has 2 coaxial digital audio
inputs ”DIGITAL IN”.
For optimum sound transmission connect the
output socket of the DVD player (DIG OUT) to
the ”DIGITAL IN 1 or IN 2” socket on the Signal
Box with a cinch cable.
The Signal Box has an electronic switch so that
it is possible to assign a digital audio input to
every AV input.
For example, if you switch a DVD player
connected to ”Euro-AV 1” to Play, the
respective assigned audio input ”DIG IN” is
selected automatically.
In this way, you can connect two DVD players,
for example, without the need for tiresome
replugging.
Note
The TV set without Dolby Digital Module can
only play PCM-Stereo sound.
to Concertos or digital receiver or Certos.
Assigning digital inputs
Switch on the ”Radio Mode”. The digital inputs
”DIGITAL IN 1” or ”DIGITAL IN 2” can be
selected directly.
1. Call up the TV menu by
pressing the MENU key.
2. Select the “Sound” line, then
press the OK key.
3. “Sound via” select the “AV
amplifier (Dig. input)” or
“Concertos”, if Concertos has
been connected.
Press the OK key
4. Press the MENU key.
5. Select the bar “Settings“
and confirm with OK.
6. Select the item “AV
settings”, then confirm with
OK.
7. Select the “Assigning Audio
digital“ line and press OK to
confirm.
8. Select "Digital IN 1 - to
AV3" for example for socket
AV3 if a DVD player or CD
player with coaxial-digital
output is connected to digital
input 1 and this device is
logged in in the "Connections"
menu.
If the video signal from a play
console is connected to the
AVS socket, the relevant device
is logged in and the digital
sound is present at the digital
input 2, then select “Digital In
2 – to AVS” etc.
9. You can complete the
settings by pressing the END
31963_021_RC3_GB 14.01.2005, 10:40 Uhr23