Magnavox 39MF412B CRT Television User Manual


  Open as PDF
of 38
 
English
13
These operations are accessible by remote control.
Some may also be accessible by control panel on the main unit.
Initialsetup
Thissectionwillguideyouthroughtheunit’sinitialsettingwhich
includesselectingalanguageforyouron-screenmenuandautoprogram,
whichautomaticallyscansandmemorizesviewablechannels.
Before you begin:
Makesuretheunitisconnectedtoantennaorcable.
1 Aftermakingallthenecessaryconnections,press toTurnOnthe
unit.
• ItmaytakeafewmomentstoTurnOntheunitforthersttime.
• InitialsetupmenuappearsautomaticallyaftertheunitisTurned
On.
2 Use▲▼toselecttheon-screenlanguagefromthechoices
(English/Español/Français)ontherightsideoftheTVscreen,then
pressOK.
3 Use▲▼toselectAntennaforTVchannelsorCableforCATV
channels,thenpressOK.
Initialsetup
Makesuretheantennaisconnectedto‘’ANTENNAIN’’jack.
Selectyoursignalsource.
Antenna
Cable
Antenna
Cable
Or
ANTENNAIN
Skip
Select OK Back Skip
– WhenAntennaisselected,theTVdetectsantennasignals.It
searchesforDTVandAnalogTVchannelsavailableinyourarea.
– WhenCableisselected,theTVdetectssignalssuppliedbycable.It
searchesforDTV,AnalogTVandCablechannelsavailableinyour
area.
• Autoprogramwillbegin.
Initialsetup
Pleasewaitwhilethesystemisscanningforchannels.
Autoprogrammingmaytakemorethan20minutesto
complete.
0%
Digital channels
0ch
Analog channels
0ch
Skip
4 Use▲▼toselectthedesiredlocationsetting,thenpressOK.
Initialsetup
LocationHomeisrecommendedfornormalhomeuse.
IntheRetailStoremode,allsettingsarefixed.
Retail
Home
Select OK
• SelectRetail,theunitwillbesetupwithpredenedsettingfor
retaildisplays.
• SelectHome,theunitissettomaximizetheenergyefciency
forhomesettinganditcanbeadjustedthroughachoiceof
pictureandsoundqualityaccordingtoyourpreference.Usethis
settingtoremovetheE-stickerifvisiblefromthedisplay.
➠
p.27
• Whentheinitialsetupiscompleted,thelowestmemorized
channelwiththeconrmationmessageofthelocationsetting
willbedisplayedontheTVscreen.
• YoumustsetHomeinstep4.Otherwise,PictureandSound
settingsyouadjustedwillnotbememorizedaftertheunitgoes
intoStandbymode.
Note
• Ifyouarenotreceivingasignalfromyourcableservice,contacttheCableprovider.
• Ifyoupress orMENUduringautoprogram,thissetupofTVchannelswillbe
canceled.
• TheinitialautoprogramfunctioncanbeexecutedforeitherAntennaorCableonly
once.Whenyouchangetheconnection(Antenna/Cable),setAutoprogramagain.
➠
p.20
• IfthereisnosignalInputfromtheantennaterminalandnooperationforseveral
secondsafteryouTurnOntheunit,helpfulhintsappears.Followtheinstructionslisted
ontheTVscreen.
Initialsetup
Nochannelisregistered.
TryAutoprogramagain?
Verifythatyouhaveacableconnectedtothe“ANTENNAIN”jack
onthebackoftheTV,thechannelinstallationprocess
searchesthisconnection.Ifyouareusingacableorsatellite
box,pleaseconfirmtheinputwhichyouhaveconnectedto
theboxandpress“SOURCE”keyontheremotecontrolto
selecttheappropriatesourceinput.
Retry
Later
Select OK Skip
After an initial setup is completed...
• Ifyouwanttoscanthechannelsautomaticallyagain.
Autoprogram
➠
p.20
• YoucanaddthedesiredcableandAnalogchannels
unmemorizedbyautoprogram.
Addchannels
➠
p.21
• Ifyouwanttochangetoanotherlanguage.
Language
➠
p.27
• Ifyouwanttochangethelocationsetting.
Location
➠
p.27
 previous next