Filter
Top Products
- 6 - EN
6
5 Select the desired start
time (hour).
Select the
minute.
8
2
3
4 Select the desired month.
Select the desired day.
1
7
Repeat the procedure in steps
5 and 6 to set the end time.
9
9. Recording Features
• Insert a tape with its record tab into the unit.
F.FW
D
ST
OP
PLA
Y
F.FW
D
ST
OP
PLA
Y
F.FW
D
PROGRAM NUMBER 1
DATE – – / – –
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
ST
OP
PLA
Y
F.FW
D
F.FW
D
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP
B SP
SLP
F.FW
D
ST
OP
PLA
Y
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 0 2 MON
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
MENU
Select an empty program
number.
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”.
F.FW
D
ST
OP
PLA
Y
F.FW
D
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
F.FW
D
ST
OP
PLA
Y
F.FW
D
Select “AM” or “PM”.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
AM
B PM
Select the desired channel.
Select the desired recording speed.
C.RESET
EXIT
STANDBY-ON
Warning: Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording VCR.
3) Press
[SPEED] on the remote control of the recording VCR to select
the desired recording speed (SP/SLP).
4) Select the “L1” or “L2” position on the recording VCR.
• To use the input jacks on the back of this unit, select "L1" position by
pressing [0], [0], [1] on the remote control or [CHANNEL ].
• To use the input jacks on the front of this unit, select "L2" position by
pressing [0], [0], [2] on the remote control or [CHANNEL ].
5) Press
[RECORD] on the recording VCR.
6) Begin playback of the tape in the playing VCR.
7) To stop recording, press
[STOP/EJECT
P
N
] on the recording VCR,
then stop playback of the tape in the playing VCR.
1) Turn the power on by pressing
[STANDBY-ON].
2) Select main menu by pressing
[MENU].
3)
Select "TIMER PROGRAMMING" by
pressing
[PLAY B]
or
[STOP C]
.
Then, press
[F.FWD g]
.
4) Select the program number
which you want to check by
pressing [PLAY B] or
[STOP C]. The details of the
program you selected will
appear on the TV screen.
• Go to the digit you want to
change by pressing
[F.FWD g] or [REW h].
Then, enter correct numbers by
pressing [PLAY B] or
[STOP C].
•
You may cancel the entire
program by pressing [REW h]
while the program number flashes.
5) Press [C.RESET/EXIT] to exit.
6) Press
[STANDBY-ON] to return
to timer stand-by mode.
Hint
• To go back one step, press
[REW h] (during steps 3 to 9).
• If there is a power failure or the unit has been unplugged for more than 30 sec-
onds, the clock setting and all timer settings will be lost.
• If the tape runs out before the end time, the unit will switch to the Stop mode
immediately, eject the tape and the power will be turned off. The TIMER indicator
will flash.
• If a tape is not in the unit or does not have the record tab, the TIMER indicator
flashes and timer recording cannot be performed. Please insert a recordable tape.
• When all the Timer Recording are completed, the TIMER indicator flashes.
To play or eject the recorded tape, press [STANDBY-ON] first, and then
press [PLAY
B
] or [EJECT
A
].
To cancel a Timer Recording that is in progress
Press [STOP/EJECT
P
N
] on the unit.
Hint
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The
remote control might affect the playing VCR’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are
not recommended.
•
You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs.
• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)
• "L2" input jacks are on the front of this unit.
Timer Recording Hints for Timer Recording
Copying a Video Tape
•
If you have connected the unit to a cable
box or satellite box as the Connection on
page 1, select the VCR to channel 3 or 4
(the RF output channel of the VCR). Then,
select the desired channel at the cable
box or satellite box. Leave the cable box
or satellite box on for timer recording.
or
or
or
ST
OP
PLA
Y
• You can program one
year in advance.
or
or
or
ST
OP
PLA
Y
or
ST
OP
PLA
Y
ST
OP
PLA
Y
or
ST
OP
PLA
Y
ST
OP
PLA
Y
or
ST
OP
PLA
Y
- M E N U -
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
To Check, Correct, or Cancel
a Timer Program
10
Turn off the
VCR for
recording.
•
TIMER indicator on the VCR lights up.
Connect
1
IN
OUT
AUDIO
VIDEO
IN
OUT
ANT
VIDEO
IN
OUT
INOUT
AUDIO
Audio/Video Cables
(not supplied)
RF Cable
(supplied)
(Back of TV)
(Back of Recording VCR*)
*Front input jacks are also available
(Back of Playing VCR)
2
Connect
CMWV405_HJ34RCD_EN.indd 6 2006/01/23 16:20:33